Consort PLSTI050EWIFI Instrukcja instalacji i sterowania - Strona 4
Przeglądaj online lub pobierz pdf Instrukcja instalacji i sterowania dla Grzałka Consort PLSTI050EWIFI. Consort PLSTI050EWIFI 8 stron. Low surface temperature panel heaters with electronic controls and wifi connection
Drukuj stronę
4
SET TIME
PRESS AND HOLD
FOR 5 SECONDS
T
EMPERATURE SET
WHEN DISPLAY SHOWS
ROOM TEMPERATURE,
PRESS TO ADJUST
1. Basic Operation
Before you can use the heater, it has to be activated
by pressing any control button. The LCD backlight will
turn on. To operate any control button, press within 2
seconds of activation.
2. Time and day setting
-
Press and hold the TIME button for 5 seconds.
Minutes are flashing - use TEMP and MODE
buttons to set minutes.
-Press TIME button
Hours are flashing - use TEMP and MODE
buttons to set hours.
-Press TIME button
Day is flashing - use TEMP and MODE
buttons to set Day.
Once you are happy with the settings, press 'Time' to
return to main screen.
When connected to the app, time will be taken
automatically from the internet.
3. Selecting operating mode
The heater has 4 operating modes:
BOOST, MANUAL, SETB, PROGRAM.
BOOST, MANUAL and PROGRAM can be selected by
pressing the MODE button to cycle through the
options. The cycle sequence will always start with
BOOST mode followed by MANUAL, SETBACK and
PROGRAM.
4. BOOST - 15 minutes
The boost feature increases the room temperature for 15
minutes.
1. Use TEMP and MODE to set the temperature.
To amend the set temperature when in Boost mode,
simply activate the display by pressing any button. Press
TEMP, then use TEMP and MODE to change the
temperature. Once the temperature is set, you can
leave the display to return to the main screen and the
settings will be saved. After 15 minutes, the heater will
return to previous operating mode.
The 15 minute period can be increased up to 4 hours by
using the PROG button. Pressing this will increase the
temperature in 15 minute increments.
This will reset back to 15 minutes after every use.
Time
Prog
Mode
Temp
5. MAN - Manual Mode
In manual mode, the heater maintains a set temperature
between 4°C and 35°C.
1. Use TEMP and MODE to set the temperature.
To amend the set temperature when in Manual mode,
simply activate the display by pressing any button. Press
TEMP, then use TEMP and MODE to change the
temperature. Once the temperature is set, leave the
display to return to the main screen and the settings will
be saved.
6. SETB - Setback Mode
Setback mode can be used for frost protection, situations
where a minimum room temperature must be
maintained. It maintains a temperature between 4°C
and 15°C.
To amend the set temperature when in Setback mode,
simply activate the display by pressing any button. Press
TEMP, then use TEMP and MODE to change the
temperature. Once the temperature is set, leave the
display to return to the main screen and the settings will
be saved. When the room temperature drops below the
set temperature the heating will be active.
7. PROG - Automatic mode
In this mode, the heater will follow the week's time / tem-
perature program.
You can temporarily override the temperature in PROG
mode by simply activating the display and using the
TEMP and MODE buttons to set the new temperature. The
new set temperature will be then maintained until the
next program step.
8. Heat symbol on the display
Every time there is a demand for heat, the display will
show the heat icon.
-
is close to the set temperature - allows for almost silent
operation.
- full heat output
Reduced heat output when the room temperature
SET PROGRAM
PRESS AND HOLD
FOR 5 SECONDS
MODE SELECTION
BOOST, MANUAL,
SETBACK AND
PROGRAM
66001185 Iss 01