Hideaway Beds Beta Bed Double Instrukcja montażu - Strona 14
Przeglądaj online lub pobierz pdf Instrukcja montażu dla Wyposażenie wnętrz Hideaway Beds Beta Bed Double. Hideaway Beds Beta Bed Double 20 stron. Wallbed frame and cabinet system
Drukuj stronęSTEP 6: Assemble Bed Face Panel Unit - Prepare and assemble Cleats
and Rails and attach to Bed Face Panel
1.
Drill necessary holes to attach the Lift Mechanism and the fold down legs. Dimensions are in Drawing 9.
STOP! If you are assembling the Bed Face Panel in the Horizontal Orientation, Drill Holes #1,#2, and #3
AND the Leg Pivot Holes must be put into the END RAILS, not the side rails as shown. The drawing
indicates where these holes must be drilled for mounting the mechanism and leg assemblies to Bed Rails for
vertical orientation; subtract 3/4" (19mm) from all dimensions for horizontal beds to allow for wood thickness.
Drill through the four Cleats at approximate 4" (100mm) intervals in both directions so they may be attached
2.
to the rails as well as to the Bed Face. Lay the rails out on the Bed Face Panel so you will not confuse left
or right and the head and front of the Bed Face final assembly.
Glue and screw the Cleats and Rails together. Be sure the Cleats are inset 3/4" (19mm) from both ends of
3.
the proper rail. Be sure that the Cleats are on the inside of the Rails. Use #8 x 1 1/4" screws for this
procedure.
Refer to Drawing 9 and drill the holes in the Side and End Rails for securing with three Confirmat screws
4.
at each corner of the Rails.
NOTE: The Bed Face Panel Unit absorbs the most weight and stress of all the Bed Cabinet components,
therefore the unit must be glued and screwed at the time of assembly. Do not finish the wood components
of this unit until it is completely assembled. This will assure maximum strength from the glued joints.
Position Bed Face Panels face down on a flat surface. Position three Stiffeners in locations shown in
5.
Drawing 10 - ends of stiffeners should be 2 3/8" (60mm) from edges of Face Panels to allow for Side Rails
and Cleats. At this time drill two rows of pilot holes in the Stiffeners approximately 4" (100mm) apart and 1"
(25mm) from both sides of the Stiffener.
ALERT: use caution not to drill into the seam of the Face Panels.
Rails [Holes #1, #2, & #3 attach Frame to Mechanism]
2 5/8"
(66.5)
3/4" x 4 1/2" x 74 1/2" (19 x 114.3 x 1892mm)
Foot
Ø 3/4" (19) Bore hole
4 1/2"
(114)
1 3/8"
Steel Leg
(35)
Pivot Hole
3/4" x 4 1/2" x 79 1/2" (19 x 114.3 x 2019mm)
Foot
Ø 3/4" (19) Bore hole
4 1/2"
(114)
1 3/8"
2 5/8"
(35)
(66.5)
Stiffeners
1.0" (25)
1.0" (25)
Single/Double Side Rail
King Side Rail
79 1/2" (2019)
Single 3/4"x4"x37 1/2" (19x102x953) / Double 3/4"x4"x52 1/2" (19x102x1334) / King 3/4"x4"x58 1/2" (19x102x1486)
3.78"
(96)
74 1/2" (1892)
18 5/8" (473)
#3
1 1/2"
1 1/32"
(38)
(26)
Ø5/16" (8) Bore Hole
#3
1 1/2"
(38)
18 5/8" (473)
9 27/32" (250)
6 1/8" (156)
#2
#1
Head
27/32"
(21.5)
Mechanism Mounting Holes
Ø5/16" (8) Bore Hole
#2
#1
6 1/8" (156)
1 1/32"
27/32"
(26)
(21.5)
9 27/32" (250)
3/4" (19)
2 1/4" (57)
3/16" (5) Dia.
3/4" (19)
3/4" (19)
Head
Drawing 9.
14.