MAK Dis-360VIR Podręcznik użytkownika - Strona 2
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Kamera bezpieczeństwa MAK Dis-360VIR. MAK Dis-360VIR 2 stron. Weatherproof & vandalproof ir dome color camera
Drukuj stronęBRIEF OF PRODUCT
* Sensor (CCD)
Adopt SONY 1/3" CCD Sensor.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Scanning Mode
NTSC or PAL mode.
* Water Resistance
IP66
* OSD SETTING
LENS
MANUAL/DC/VIDEO
AUTO,FLK,1/50,1/250,1/500,1/2000,1/40000,
SHUTTER
1/5000,1/10000,1/100000
BRIGHTNESS
EXPOSURE
AGC
LOW/MIDDLE/HIGH/OFF
D-WDR
OFF/ON(LEVEL:0-63)
RETURN
ATW1/ATW2/AWC-SET/MANUAL:(INDOOR、OUTDOOR、
WHITE BAL
MANUAL)
OFF
BACK
BLC:AREA SEL/AREA STATE/GAIN/HEIGHT/LEFT/RIGHT/
LIGHT
TOP/BOTTOM
HLC:LEVEL(0-255)/ MODE(ALL DAY/NIGHT ONLY)
DPC
COVER THE LENS THEN PRESS ENTER KRY
COLOR
BURST(OFF/ON)/IR SMART(OFF/ON:IR GAIN/
DAY &
B/W
HEIGHT/WIDTH/LEFT/RIGHT/TOP/ BOTTOM)/IR
NIGHT
LEVEL(HIGH/LOW)
AUTO
D-N(LEVEL/DELAY) /N-D(LEVEL/DELAY)
CAM TITLE
OSD
SET
AREA SEL:AREA1-4
MOTION
AREA STATE:OFF/ON
OFF/ON
HEIGHT/WIDTH/LEFT/RIGHT/TOP/BOTTOM /
DEGREE/VIEW
AREA SEL:AREA1-8
PRIVACY
AREA STATE:OFF/ON
OFF/ON
HEIGHT/WIDTH/LEFT/RIGHT/TOP/BOTTOM /
PARK.LINE
OFF/ON(LT/LB/RT/RB/F/N/T)
SPECIAL
LENS SHAD:OFF/ON
2DNR:OFF/ON
MIRROR:OFF/ON
FONT COLOR:FONT(0-15)/ID&TITLE(0-15)
CONTRAST:0-255 SHARPNESS:0-31
IMAGE ADJ
NEG.IMAGE:OFF/ON
DISPLAY:CRT(PED LEVEL:0-63/COLOR GAIN:0-
255)/LCD(GAMMA:0-1/PED LEVEL:0-63/
COLOR:0-255)/USER(GAMMA:0-1/PED LEVEL:0-
63/COLOR:0-255)
RESET
FACTORY RESET
EXIT
CONNECTING
KEY BOARD
UP
LEFT
DOWN
0－255
TROUBLE AND SOLUTION
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
ON/OFF
3. The picture background color changes continuously
. The fluorescent lamp's electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
COLOR
. The power supply's voltage unstable.
. Connecting cables not connect correctly or have high impedance.
Notes：
●The power supply must through safe attestation. Its output voltage,
current, voltage polarity and operating temperature must match the
camera's requirement.
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply's cable and
video output cable should not be too long.
Monitor
Dis-360VIR
MENU
Link wire rule：
RIGHT
Video
Power
PRESS
DC12V Power Supply
INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits
Dis-360VIR
latest SONY technical of sensor and driver. The most at-
Video
tractive characteristics are small and easy hidden, suits
the elevator and corridor. In addition, it owns the charac-
ters of high definition and stability, strong anti-jamming,
rich and real color. Fixing and using this model are con-
venient too. It is very good for you to apply to your CCTV
DC12V
system.
Please read this instruction manual carefully to en-
sure proper use of the product.
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
The symbol is intended to alert the user to the presence of
uninsulated 'dangerous voltage' within the product's
enclosure that may be of sufficient Magnitude to constitute
a risk of electric shock to persons.
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Note:
● Please note the camera's operating temperature and its using
environment requirement. Avoid using the camera at too high or
too low temperatures. The operating temperature is -30~+60℃.
(Recommendatory operating temperature is -10~+45℃.)
● Never make the camera face the sun or bright object. Other-
wise, it will damage the CCD.
● Do not mount the camera near by the radiator or heater.
product. We adopt the
CAUTION:
TO REDUCE THE RISK OF ELECTRIC