Century Helicopter Products Hummingbird Elite 3D Pro Instrukcja montażu i obsługi - Strona 7

Przeglądaj online lub pobierz pdf Instrukcja montażu i obsługi dla Zabawka Century Helicopter Products Hummingbird Elite 3D Pro. Century Helicopter Products Hummingbird Elite 3D Pro 12 stron.
Również dla Century Helicopter Products Hummingbird Elite 3D Pro: Instrukcja obsługi (10 strony)

Drukuj stronę

Century Helicopter Products Hummingbird Elite 3D Pro Instrukcja montażu i obsługi

1. Specifications

Section 9: Main Gear Train Assembly

Bags Used:

CNE313, CNE314, CNE319, CNE250

Main rotor head assembly (9-1, 9-2, 9-3, 9-4, 9-5)

Using the built

Upper Main Frame

remaining items from bag CNE313 will be needed here.

33) Insert CNE314

Swashplate

Collar. There are three control balls on the Swashplate outer arms and one

straight guide. Insert the

Straight Guide

Bracket.

There are two

Washers, two

Brass

parts bag CNE313.

34) Insert the

Swashplate

to the

Brass Washer

below the

Main Shaft Collar

(do not tighten until 9-5).

35) Insert the

Main Shaft

into the

of the

Upper Frame Plate

36) Open parts bag CNE319

Plate

and the

Large Beveled Gear

Teeth of the

Tail Crown Gear

37) Insert the

Main Shaft

through the

Washers

in CNE313 onto the

parts bag CNE250

Autorotation Hub &

Locking Insert

into the gear into the one-way bearing with the opening facing

outward. Slide the

Autorotation Hub & Gear

tapered aluminum portion

Washers.

38) Expose the bottom hole of the

into the bottom hole in the

in the

Autorotation Locking Insert

Jesus Pin

in place.

39) Insert 7.80mm

Jesus Pin

Black Washers.

Use long nose pliers to guide the

middle hole of the

Main

Shaft.

40) Align the

Jesus Pin

to the opening in the

assembly upward locking the

41) (Both lower

Jesus Pins

are now aligned and the gear train is ﬂush to the

bottom

Bearing

of the

Upper Frame

the lowest position on the

upper

Bearing

inside the

to complete the assembly (the gear train at this time should have virtually no

vertical movement / play).

9-4

Tail Crown Gear

#CNE319

and the built

Rotor Head

to the

Main Shaft

directly under the Rotor Hub

of the swashplate to the

and one 11.70mm

Black Washers

Main Shaft

followed by the

Main Shaft

Collar. Start the

M3x3 Set Screw

Mast

Tower, sliding it through ﬂush to the bottom

& ball bearing.

Tail Crown

Gear. Insert it between the

to allow the gear teeth to mesh (9-2).

should be facing away from the

Tail Crown

Gear. Slide the two

Main Shaft

below the

Tail Crown

Gear. Insert the black

onto the

Main Shaft

of the

Autorotation Hub

to touch one of the

Main

Shaft. Insert the supplied 4.70mm

Main

Shaft, align the

Jesus Pin

and pull upward on the rotor head to lock the

found in CNE313 into the

Main Shaft

Jesus Pin

Tail Crown Gear

Jesus Pin

in place.

Plate). Move the

Main Shaft Collar

Main Shaft

pressing the

Brass Washer

Mast

Tower. Locktite and tighten the

Jesus Pin

#CNE313

Black Washers (2)

#CNE313

Assembly. Most of the

Antirotation

Jesus Pin

Main Shaft Collar

and

into the

Upper Frame

Plate.

Black

Gear. Open

Autorotation

to allow the

Black

Jesus

to the opening

above the two

through the lower-

and pull the shaft

against the

M3x3 Set Screw

Autorotation Hub & Gear

Assembly (tapered portion)

#CNE250

9-1

Main Shaft Collar

#CNE313

Brass

Washer

#CNE313

9-2

Tail Crown Gear

#CNE319

9-3

Autorotation

Locking Insert

#CNE250

Main Shaft Collar

#CNE313

9-5

Rotor Hub

Collar

#CNE303

Swashplate

#CNE314

Large Beveled

Tail Drive Gear

#CNE305

Autorotation Hub

#CNE250

Autorotation

Gear #CNE250

Jesus Pin

#CNE250

M3x3 Set

Screw

#CNE313