IKEA IHW7302YS0 Instrukcja obsługi i konserwacji - Strona 5
Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Okap wentylacyjny IKEA IHW7302YS0. IKEA IHW7302YS0 44 stron. 30"(76.2cm) wall-mount canopy range hood
Drukuj stronęINSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Level
•
Drill with 11¼ '' (3.0 cm), 3/8"(9.5 mm), and 3/le" (4.8 mm)
drill bits
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof
caulking compound
•
Vent clamps
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
•
Phillips screwdriver
•
Metric hex key set
Parts needed
•
Home power supply cable
•
1/2"(12.7 mm) UL listed or CSA approved strain relief
•
3 UL listed wire connectors
For vented installations,
you will also need:
•
1 wall or roof cap
•
Metal vent system
For non-vented
(recirculating)
installations,
you will also
need:
•
Charcoal Filter Kit Part Number W10412939 for non-vented
(recirculating)
installations only. See "Assistance
or Service"
section to order.
•
6" (15.2 cm) dia. round metal vent duct - length required is
determined by ceiling height.
•
2- Flat washers
•
4- 4.2 x 8 mm screws
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the filter on the rear wall of the vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented
(recirculating) Installation see "For Non-
vented (recirculating)
Installation Only" in "Connect Vent System"
section. Charcoal Filter Kit Part Number W10412939 is available
from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
7W'
8½"
(18.3 crn)
(20.7 crn)
Parts supplied
Remove parts from packages. Check that all parts are included.
•
Hood canopy assembly with ventilator and light bulbs
installed
•
Vent transition with back draft dampers installed
•
Metal grease filter(s)
•
Vent cover support bracket
•
Mounting template
•
Air deflector with extensions (for non-vented
installations)
•
2-piece vent cover
•
6- 3.5 x 6.5 mm screws
•
2 - 2.9 x 6.5 mm screws
•
6- 5 x 45 mm mounting screws
•
6- 8 x 40 mm wall anchors
•
T10 Torx '_t adapter
•
T20 Torx '_tadapter
®I-TORX is a registered trademark
of Saturn Fasteners,
Inc.
24 It
(61.0 crn)
42V8" (107.0 cm) rnin.
"61" (155.0 crn) max.
*'653/8 '' (166.0 crn) max.
30" (76.2 crn)
*For non-vented
(recirculating) installations
**For vented installations
187/8'' (48.0 crn)