IKEA W11212416C Instrukcje użytkownika - Strona 13
Przeglądaj online lub pobierz pdf Instrukcje użytkownika dla Zmywarka IKEA W11212416C. IKEA W11212416C 48 stron.
Drukuj stronę
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
DISHWASHER IS NOT OPERATING PROPERLY
PROBLEM
Dishwasher does not
run or stops during a
cycle
The Clean light is
flashing
Dishwasher will not fill
Dishwasher seems to
run too long
Water remains in the
dishwasher
Detergent remains in
the covered section of
the dispenser
White residue on the
front of the access
panel
Odor in the dishwasher
Condensation on the
kitchen counter
(built-in models)
DISHES DO NOT DRY COMPLETELY
Dishes do not dry
completely
Dishes are not dry
PROBLEM
Excess moisture on
racks and dishwasher
interior
Troubleshooting
to possibly avoid the cost of a service call.
In the U.S.A., www.ikea.com
POSSIBLE CAUSES AND/OR SOLUTIONS
Is the door closed tightly and latched?
Is the right cycle selected?
Is there power to the dishwasher? Has a household fuse blown or has a circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues, call an electrician. Has the motor stopped
due to an overload? The motor automatically resets itself within a few minutes. If it does
not restart, call for service.
Is the water shut-off valve (if installed) turned on?
It is normal for certain cycles to repeatedly pause for several seconds during the main wash.
Call for service.
Is the overfill protection float able to move up and down freely? Press down to release.
The dishwasher can run up to 3¹⁄
Is the water supplied to the dishwasher hot enough? The dishwasher runs longer while heating water.
Is the dishwasher cycle time within the cycle times? See cycle selections wash times. A delay
automatically occurs in some wash and rinse cycles until the water reaches the proper temperature.
This dishwasher is equipped with an optical sensor wash that detects water temperature, soil, and
detergent amount. Wash cycles are adjusted based on what is sensed.
IMPORTANT: The very first wash cycle after installation in your home will be adjusted to include an
additional 2 rinses. This cycle must not be interrupted for proper sensor adjustment. If this adjustment
cycle is canceled or stopped before the Clean light comes on at the end of the cycle, the next wash cycle
will repeat this sensor adjustment.
Is the cycle complete?
Is the cycle complete?
Is the detergent lump free? Replace detergent if necessary.
Is the dispenser door blocked by dishes or cookware when the dishwasher door is closed?
Was too much detergent used?
Is the brand of detergent making excess foam? Try a different
brand to reduce foaming and eliminate buildup.
Are dishes washed only every 2 or 3 days? Run a rinse cycle once or twice a day until you have a full load.
Does the dishwasher have a new plastic smell? Run a vinegar rinse as described in "Dishwasher Care."
Is the dishwasher aligned with the countertop? Moisture from the vent in the dishwasher console can form
on the counter. Refer to the Installation Instructions for more information
Did you use a rinse aid? Your dishwasher is designed to use rinse aid for good drying performance.
Without rinse aid, your dishes and dishwasher interior will have excessive moisture. The Heat Dry option
will not perform as well without rinse aid.
Did you load your dishwasher to allow proper water drainage?
Do not overload. Use a liquid rinse aid to speed drying.
Are the plastics wet? Plastics often need towel drying.
Is the rinse aid dispenser empty?
Did you use an air-dry or energy-saving dry option? Use a heated drying option for dryer dishes.
POSSIBLE CAUSES AND/OR SOLUTIONS
Check the rinse aid indicator to see that there is rinse aid in the dispenser.
In Canada, www.ikea.com
hours depending on soil level, water temperature, cycles, and options.
2
13