IKEA W11212416C 사용자 지침 - 페이지 13

{카테고리_이름} IKEA W11212416C에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. IKEA W11212416C 48 페이지.

페이지 인쇄

1. Troubleshooting

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

DISHWASHER IS NOT OPERATING PROPERLY

PROBLEM

Dishwasher does not

run or stops during a

cycle

The Clean light is

flashing

Dishwasher will not fill

Dishwasher seems to

run too long

Water remains in the

dishwasher

Detergent remains in

the covered section of

the dispenser

White residue on the

front of the access

panel

Odor in the dishwasher

Condensation on the

kitchen counter

(built-in models)

DISHES DO NOT DRY COMPLETELY

Dishes do not dry

completely

Dishes are not dry

PROBLEM

Excess moisture on

racks and dishwasher

interior

Troubleshooting

to possibly avoid the cost of a service call.

In the U.S.A., www.ikea.com

POSSIBLE CAUSES AND/OR SOLUTIONS

Is the door closed tightly and latched?

Is the right cycle selected?

Is there power to the dishwasher? Has a household fuse blown or has a circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues, call an electrician. Has the motor stopped

due to an overload? The motor automatically resets itself within a few minutes. If it does

not restart, call for service.

Is the water shut-off valve (if installed) turned on?

It is normal for certain cycles to repeatedly pause for several seconds during the main wash.

Call for service.

Is the overfill protection float able to move up and down freely? Press down to release.

The dishwasher can run up to 3¹⁄

Is the water supplied to the dishwasher hot enough? The dishwasher runs longer while heating water.

Is the dishwasher cycle time within the cycle times? See cycle selections wash times. A delay

automatically occurs in some wash and rinse cycles until the water reaches the proper temperature.

This dishwasher is equipped with an optical sensor wash that detects water temperature, soil, and

detergent amount. Wash cycles are adjusted based on what is sensed.

IMPORTANT: The very first wash cycle after installation in your home will be adjusted to include an

additional 2 rinses. This cycle must not be interrupted for proper sensor adjustment. If this adjustment

cycle is canceled or stopped before the Clean light comes on at the end of the cycle, the next wash cycle

will repeat this sensor adjustment.

Is the cycle complete?

Is the detergent lump free? Replace detergent if necessary.

Is the dispenser door blocked by dishes or cookware when the dishwasher door is closed?

Was too much detergent used?

Is the brand of detergent making excess foam? Try a different

brand to reduce foaming and eliminate buildup.

Are dishes washed only every 2 or 3 days? Run a rinse cycle once or twice a day until you have a full load.

Does the dishwasher have a new plastic smell? Run a vinegar rinse as described in "Dishwasher Care."

Is the dishwasher aligned with the countertop? Moisture from the vent in the dishwasher console can form

on the counter. Refer to the Installation Instructions for more information

Did you use a rinse aid? Your dishwasher is designed to use rinse aid for good drying performance.

Without rinse aid, your dishes and dishwasher interior will have excessive moisture. The Heat Dry option

will not perform as well without rinse aid.

Did you load your dishwasher to allow proper water drainage?

Do not overload. Use a liquid rinse aid to speed drying.

Are the plastics wet? Plastics often need towel drying.

Is the rinse aid dispenser empty?

Did you use an air-dry or energy-saving dry option? Use a heated drying option for dryer dishes.

POSSIBLE CAUSES AND/OR SOLUTIONS

Check the rinse aid indicator to see that there is rinse aid in the dispenser.

In Canada, www.ikea.com

hours depending on soil level, water temperature, cycles, and options.