ALIBI ALI-BC1720LPC Szybka instalacja i instrukcja obsługi - Strona 4
Przeglądaj online lub pobierz pdf Szybka instalacja i instrukcja obsługi dla Kamera IP ALIBI ALI-BC1720LPC. ALIBI ALI-BC1720LPC 4 stron. 720p hd-tvi license plate camera
Drukuj stronęZoom in: Set the Zoom In function to 100, 90, .. 50 as needed. 50 is the highest zoom in.
—
Lamp: Set the Lamp option to Off, On, or Auto. If you select On or Auto, open the submenu to
—
set the brightness (1 .. 5).
RESET: Select reset to set all parameter values to the factory default setting.
•
SAVE & EXIT: Select Save & Exit to close the OSD menu.
•
Specifications
Camera
Image Sensor
1.27 Mega Progressive Scan CMOS
Signal system
PAL/NTSC
Effective Pixels
1305 (H) * 977 (V)
Min. Illumination
0.001 Lux @ (F1.2, AGC ON),0 Lux with white light
Shutter Time
1/100 s to 1/50,000 s
Lens
6 ~ 22 mm motorized VF lens
Lens Mount
Φ14
Day & Night
Color
Synchronization
Internal synchronization
Video Frame Rate
720p @ 25 fps / 720p @ 30 fps
HD Video Output
1 turbo HD output
CVBS Video Output
1 Vp-p composite output(75 Ω / BNC)
S/N Ratio
> 62 dB
Menu
Auto Gain
Low/Middle/High/Off
D/N Mode
Color
White Balance
Auto/Manual
Private Mask
On/Off, maximum 8 zones
Motion Detection
On/Off, maximum 4 zones
Exposure Mode
Global Exposure/Digital WDR
3D Noise Reduction
Low/Middle/High/Off
Language
English/Chinese
Function
Contrast/Sharpness/Saturation/Mirror/Digital zoom
White Light Control
On / Off / 1-5 adjustable level
General
Operating Conditions
-40 °F ~ 140 °F (-40°C ~ 60°C )
Humidity 90% or less (non-condensing)
Power Supply
12 Vdc ±15%
Power Consumption
Max. 5W
Protection Level
IP66
Light Distance
98 ~ 131 ft (30 ~ 40 m)
Communication
Up the coax
Protocol: Pelco-C (CVBS output), HD-TVI output)
Dimensions
5.28 × 4.57 × 11.54 in. (134 × 116 × 293 mm)
Weight
24.7 oz (700 g)
www.observint.com
4
CLEANING
Clean the camera lens with an approved glass cleaning solution and a lint free cloth.
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
•
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
•
These may cause damage to the surface over time.
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
CAUTION
carefully follow the accompanying instructions.
TROUBLESHOOTING
Problem
Possible Cause
Nothing appears on the screen
- Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark.
- Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and
- Verify that the camera is correctly connected to an appropriate regulated
the surface of the camera is hot.
power source.
The image on the monitor flickers
- Make sure that the camera isn't facing direct sunlight or fluorescent light.
If necessary,change the camera position.
© 2015 Observint Technologies. All rights reserved.