Avanti IM3202SS Instrukcja obsługi - Strona 11

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Kostkarka do lodu Avanti IM3202SS. Avanti IM3202SS 20 stron. Avanti refrigerator ice maker combo model number: im320299

Drukuj stronę

1. Parts and Features

ALL THE NECESSARY HARDWARE IS NOT PROVIDED FOR INSTAL LATION SO IT IS

NECESSARY TO HIRE A PROFESSIONAL LICENSED PLUMBER TO COMPLETE THE

INSTALLATION.

CONNECT TUBING (SUPPLIED WITH UNIT) TO THE NEAREST COLD WATER SOURCE.

CONNECT SUFFICIENT TUBING TO THE UNIT TO ALLOW THE APPLIANCE TO BE MOVED

FREELY FOR CLEAN ING AND SERVICE. ALSO MAKE SURE THAT THE TUBING IS NOT

PINCHED OR DAMAGED DURING TRANSPORTATION.

POSITION UNIT TO ALLOW FREE AIRFLOW THROUGH THE FRONT GRILL

(

1). WIPE OUT INSIDE OF UNIT AND ICE BUCKET WITH A DAMP

SEE SKETCH

CLOTH.

REVERSING THE DOOR SWING OF YOUR APPLIANCE

THIS APPLIANCE HAS THE CAPABILITY OF THE DOOR OPENING FROM EITHER THE LEFT OR

RIGHT SIDE. THE UNIT IS DELIVERED TO YOU WITH THE DOOR OPENING FROM THE LEFT

SIDE. SHOULD YOU DESIRE TO REVERSE THE OPENING DIRECTION, PLEASE CALL

CUSTOME R SERVICE FOR REVERSAL INSTRUCTIONS.

INITIAL START-UP ICE MAKING OPERATION

1. PLUG THE APPLIANCE INTO A 115/120V POLARIZED AND GROUNDED WALL ELECTRICAL

OUTLET.

2. TO PRODUCE ICE, PLACE THE ON-OFF SWITCH, LOCATED ON THE FRONT GRILLE, IN THE

"ON" POSITION.

3. SET THE CONTROL TEMPERATURE DIAL TO POSITION 5 OR 6 (MARKED ICE MAKING).

IN THIS UNIT, THE CONTROL DIAL IS ALSO USED FOR SETTING THE TEMPERATURE IN THE

ICE MAKER REFRIGERATOR SECTION USING POSITIONS 1 TO 4 (4 BEING THE COLDEST).

4. MAKE SURE THE WATER SUPPLY IS ON. AS SOON AS THE INNER MECHANISM REACHES

THE PROPER TEMPERATURE, THE ICEMAKER MECHANISM WILL FILL THE MOLD WITH

WATER.

5. THE FIRST CUBES MAY BE SMALL BECAUSE OF AIR IN THE WATER LINE. LATER CUBES

WILL BE OF STANDARD CRESCENT MOON TYPE SIZE.

6. APPROXIMATE TIME FOR THE FIRST CYCLE IS BETWEEN 30-40 MINUTES.

7. EACH CYCLE APPROXIMATELY WILL TAKE 140 ML OF WATER SO YOU SHOULD HAVE A

FULL TRAY, AFTER 11 HOURS.

IMPORTANT: THROW AWAY ALL ICE CUBES MADE DURING THE FIRST 3 HOURS OF

OPERATION.

WHEN THE ICE BUCKET IS FULL, THE ICE MAKING MECHANISM WILL

AUTOMATICALLY SHUT OFF. HOWEVER THE REFRIGERATION SYSTEM

WILL CONTINUE TO COOL AND MAINTAIN THE CUBES SUPPLY.

ICE DELIVERY MAY BE INTERRUPTED BY RAISING THE METAL ARM INTO

AN UPRIGHT POSITION (

IF THE ICEMAKER IS NOT USED REGULARLY, IT IS RECOMMENDED THAT

THE ICE BUCKET BE EMPTIED PERIODICALLY TO INSURE FRESH ICE.

SOMETIMES THE CUBES MAY APPEAR CLOUDY. THIS IS CAUSE OF NO CONCERN AND HAS

NOTHING TO DO WITH THE TASTE OR CHEMICAL MAKE-UP OF THE WATER.

THE FRONT GRILL SHOULD BE KEPT FREE OF DUST AND LINT TO PERMIT FREE AIRFLOW.

THIS UNIT SHOULD BE DEFROSTED APPROXIMATELY EVERY 4-6 WEEKS OR WHEN FROST

ON THE APPLIANCE WALLS IS EXCESSIVE OR ¼" THICK. TO DEFROST, TURN THE UNIT

OFF, REMOVE CUBES AND KEEP DOOR OPEN AT LEAST TWO INCHES.

OPERATING YOUR ICE MAKER

SEE SKETCH

SKETCH 1

SKETCH 2