Jandy Infinite WaterColors IWCP50W100 Instrukcja instalacji i obsługi - Strona 6
Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Kontroler Jandy Infinite WaterColors IWCP50W100. Jandy Infinite WaterColors IWCP50W100 12 stron. Led lighting
Również dla Jandy Infinite WaterColors IWCP50W100: Instrukcja instalacji i obsługi (12 strony), Podręcznik (2 strony)
Drukuj stronę
ENGLISH
7.
Fill the pool until the underwater light is
completely submerged in water before operating
the light for more than 10 seconds. The light
will heat up quickly when operated outside of
water. Turn on circuit breaker, which operates the
Infinite WaterColors LED Light Controller. To
check for proper operation, Refer to Section 5,
Controller Wiring Options.
WARNING
Never operate this underwater light for more than
10 seconds unless it is totally submerged in water.
Without total submersion, the light assembly will get
extremely hot, which may result in serious burns or in
breakage of the bulb or lens. This may result in serious
injury to pool or spa users, installers, or bystanders or
damage to property.
Section 4. Existing Pool or Spa
Installation
WARNING
Risk of Electrical Shock or Electrocution.
This underwater light must be installed by a licensed
or certified electrician or a qualified pool serviceman
in accordance with the National Electrical Code and
all applicable local codes and ordinances. Improper
installation will create an electrical hazard, which could
result in death or serious injury to pool or spa users,
installers or others due to electrical shock, and may
also cause damage to property.
Always disconnect the power to the color light at the
circuit breaker before installing or servicing the light.
Failure to do so could result in death or serious injury
to serviceman, pool or spa users or others due to
electrical shock.
4.1
Preparing the Light Fixture for
Replacement
Verify that the pool meets the requirements of the current
National Electrical Code
®
and ordinances. A licensed or certified electrician must
install the electrical system to meet or exceed those
requirements before the underwater light is installed.
Some of the requirements of the National Electrical
Code, which the pool's electrical system must meet,
are as follows:
Page 6
Jandy
Infinite WaterColors
®
(NEC) and all local codes
|
Pool & Spa LED Lights
Installation and Operation Manual
™
WARNING
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, which
could result in serious injury or death. A Ground
Fault Circuit Interrupter (GFCI, in Canada: Class A
type) should be used if required by the transformer
manufacturer or if required by the local applicable
code and/or Authority Having Jurisdiction (AHJ). When
a GFCI is used, the conductors on the load side of
the GFCI circuit shall not occupy conduit, boxes, or
enclosures containing other conductors unless the
additional conductors are also protected by a GFCI.
Test the GFCI on a routine basis. Refer to local codes
for complete details.
1.
The junction box or Infinite WaterColors LED
Light Controller suitable for direct conduit
connection to lights must be located at least (8)
inches above water level, at least four (4) inches
above ground level, and at least (48) inches (4)
feet from the edge of the pool, or as required by
local code, See Figure 1.
2.
The light fixture and all metal items within five
(5) feet of the pool must be properly electrically
bonded to a reliable point of grounding.
3.
The wet niche must be properly installed so that
the top edge of the underwater light's lens is at
least (18) inches below the surface of the water in
the pool. See Figure 1.
4.
The wet niche must be properly electrically
bonded and grounded via the No. 8 AWG ground
connector located at the rear of the niche. See
Figure 1.
To be certain that the pool's electrical system meets
all applicable requirements, the electrician should also
consult the local building department.
4.2
Replacing the Light Fixture
NOTE
Perform these steps only after the electrical system
requirements are met.
WARNING
Failure to bring the pool's electrical system up to code
requirements before installing the underwater light
will create an electrical hazard which could result in
death or serious injury to pool or spa users, installers,
or others due to electrical shock, and may also cause
damage to property.