Gardena WSP 7000 Instrukcja obsługi - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Pompa wodna Gardena WSP 7000. Gardena WSP 7000 8 stron. Submersible pump / dirty water pump
Również dla Gardena WSP 7000: Instrukcja obsługi (14 strony), Instrukcja obsługi (14 strony)

Drukuj stronę

Horizontal or

Loosen the regulator by turning it anti-clockwise until you

second outlet

achieve the desired water flow from the vertical pipe of the

(➔ operating a stream)

fountain / water feature.

In order to operate a stream we recommend the connector

of a 1" (25 mm) GARDENA Spiral Pond Hose, Art. No. 7896.

Connect it to the volume control of the second outlet and run

the other end of the hose to the source of the stream.

You may connect other terminals to the second outlet.

For example, a separately installed water jet may be operated

via the GARDENA Fountain / Light Bracket, Art. No. 7886.

If necessary fix the light jet base with two screws.

Information:

This significantly reduces the volume of the vertical water jet.

If the max. delivery capacity of the second outlet is to be used

then the vertical outlet should be closed with the end cap sup-

plied.

Example: Hose pipe connection with the GARDENA

Fountain / Light Bracket

To achieve the maximum power of your pump we recommend

you use a 25 mm (1") GARDENA Spiral Pond Hose, Art. No.

7896, together with the GARDENA Suction Hose Fittings, Art.

No. 1724.

Alternatively, you can use the 19 mm (3 /4") GARDENA Pond

Hose, Art. No. 7895, together with the GARDENA "Profi"

Maxi-Flow System Threaded Tap Connector, Art. No. 2802,

and the GARDENA "Profi" Maxi-Flow System Hose Connector,

Art. No. 2817.

Care Instructions

Cleaning the filter tank

Filter tank and pump should be free from dirt particles!

How to clean :

Disconnect the plug!

Remove the pump from the water.

If necessary remove the gravel.

Clean the pump and the filter using a water jet.

If there are deposits of dirt inside the pump then dismantle the

casing (➔ ➔ see "Dismantling ") and carefully clean the interior

fittings with water.

Information: Do not use any hard objects or strong detergents!

Blocked feed impeller

If the feed impeller becomes blocked, the pump and the filter

should be cleaned (see above).

Dismantling

7. Turn the pump casing

towards the front and remove it! Do not tilt !

8. Hold the rotor by the feed impeller and pull the complete unit

out of the motor casing

9. Now you may remove the filter ring

the motor casing.

Then assemble all the fittings reversing the order and direction

in which they were dismantled. Please take care that the seal

ring

➔ Make sure while assembling that you attach the pump casing

with the pressure joint being cated, press it firmly and then

turn it straight to the right.

Storage

Where to store

The pump should be stored out of the reach of children.

1. Take the pump out of the water and store away from frost

before the first frost sets in.

2. Clean and check the pump carefully.

3. Store the pump in a container filled with water.

The mains plug must not be submerged.

Complaints / Repairs

If a fault occurs, the pump attempts to switch itself on up to

10 times. If the pump still fails to start, it switches itself off auto-

matically after 40 seconds.

➔ Remove mains plug and clean the pump if necessary.

If you have any problems with your Fountain / Stream Pump, please

contact our Service or return the defective unit together with a

short description of the problem – in case of guarantee, with the

warranty card duly completed and signed – postage paid to one

of the GARDENA Service Centres listed on the back of this leaflet.

The mains cable must only be replaced by GARDENA.

Product liability

We expressly point out that, in accordance with the product

liability law, we are not liable for any damage caused by our

units if it is due to improper repair or if parts exchanged are not

original GARDENA parts or parts approved by us, and, if the

repairs were not carried out by a GARDENA Service Centre.

The same applies to spare parts and accessories.

1. Disconnect the plug!

2. Remove the pump from the water.

3. If necessary remove the gravel.

4. Pull the pump pointing vertically

upwards out of the filter tank.

5. Pull the suction filter casing

and remove it.

6. Remove the foam filter

from the

suction piece of the pump.

to the left and then pull it straight

and the seal ring

is properly re-fitted.

forwards

from