Garmin G500 Instrukcja obsługi - Strona 6

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Wyświetlacz awioniki Garmin G500. Garmin G500 14 stron. Primary flight and multifuction display system
Również dla Garmin G500: Skrócona instrukcja obsługi (2 strony), Podręcznik (40 strony)

Drukuj stronę

2.4 Servicing Information

None. In the event of system failure, troubleshoot the G500/G600 system in accordance with Section

2.6 Troubleshooting Information.

If the Mid-Continent Instruments 4300-4XX Electric Attitude Indicator or MD420 battery pack is installed,

the battery or batteries may be charged by one of the following methods:

1. Keep the battery or batteries plugged into the Attitude Indicator or Battery Module. Apply power

to the aircraft and run the unit overnight (approx. 15 hours) at the rated voltage.

2. Float Charging: Disconnect the battery or batteries from the indicator or module. Connect the

battery or batteries to a constant voltage source (battery plug (pin 1) red wire = positive) of 20.4

to 20.6 VDC continuously. Float charging may take 24 hours or longer to charge a battery pack.

3. Routine Charging: Disconnect the battery or batteries from the indicator or module. Connect the

battery or batteries to a constant voltage source (battery plug pin 1 red wire = positive) of 21.6 to

22.1 VDC with a current limit of 0.1 ampere maximum. When the charging current drops to

approximately 5mA, the battery is fully charged and should be disconnected. Leaving 21.6 to

22.1 VDC charge voltage on the battery for an extended time will degrade its life. If continuous

maintenance of the charge is desired, refer to step 2, Float Charging.

Battery out gassing and a rotten egg odor may occur due to

prolonged high rate overcharging and may result in battery

4. The Mid-Continent Instruments Battery Charger/Tester P/N 36029 may be used. This Battery

Charger/Tester will apply an initial charge, per step 3 above, and then automatically switch to

maintain a float charge, per step 2 above, indefinitely after initial charging is complete.

2.5 Periodic Maintenance Instructions

All G500/G600 system LRUs are designed to detect internal failures. A thorough self-test is executed

automatically upon application of power to the units, and built-in tests are continuously executed.

Detected errors are indicated on the GDU 620 display via failure annunciations.

Operation of the G500/G600 system is not permitted unless an inspection as described in this section

has been completed within the preceding 12 calendar months. Conduct a visual inspection (look for

signs of wear, deterioration, or damage to wires, switches, backshells, connectors, overbraid, bonding

straps or foil) of the G500/G600 system LRUs and wiring harnesses to ensure installation integrity:

Inspect all units for security of attachment, including visual inspection of brackets and other

supporting structure attaching all units to the airframe.

2. Inspect all switches, knobs and buttons for legibility.

3. Visually inspect each unit's wiring for chafing or wear at each termination.

4. Visually check for any signs of corrosion.

2.5.1

Transient Voltage Suppressors (non-metallic aircraft only)

The GDU 620 #1, GRS 77 #1, GDC 74( ) #1, and GAD 43 (if installed) may have a TVS located at each

LRU. The electro-mechanical and electronic standby indicator (if installed) may have a TVS located at

the indicator and/or at the power bus. See G500/G600 AML STC Installation Manual Table K-2 to help

locate TVS installations. These components must be tested every 24 calendar months in accordance

with section 8.3.1 of the G500/G600 AML STC Installation Manual.

G500/G600 PFD/MFD System

Instructions for Continued Airworthiness

****WARNING****

damage. The battery assembly must be replaced if

out gassing has occurred.

190-00601-00 Rev. L

Page 6 of 14