Brother GTX600NB Podręcznik bezpieczeństwa - Strona 2

Przeglądaj online lub pobierz pdf Podręcznik bezpieczeństwa dla Drukarka Brother GTX600NB. Brother GTX600NB 2 stron. Garment pra inter
Również dla Brother GTX600NB: Instrukcja konfiguracji (45 strony)

Drukuj stronę

3. Warning labels

Waste ink tank

Waste water

tank

Cleaning solution bottle

9 L

Cleaning solution bottle

18 L

1 4 6

3 5 7

Required Tools

Phillips screwdriver: M3 to M5

Disassembling

1) Remove the Cover of BACK SIDE bottom center.

2) Remove the Lithium Battery (1) by pulling out the holder

in the direction of the arrow.

(1)

Checking the installation site

17.7 in. (45 cm) or more

31.5 in. (80 cm)

or more

15.7 in. (40 cm)

or more

31.5 in. (80 cm)

or more

31.5 in. (80 cm)

or more

129.5 in. (329 cm)

116.5 in. (296 cm)

or more

 When installing the printer, avoid any place that presents direct sunlight or a large amount of dust.

 The size is 73.6 in. (width) x 75.6 in. (depth) x 57.5 in. (height) (187 cm (width) x 192 cm (depth) x 146 cm (height)). The

main unit weighs 730 kg (1609 lb).

 Do not use an extension cable.

 Keep a minimum workspace of 31.5 in. (80 cm) in front and on the left and right sides of the printer. Also, keep 15.7 in. (40

cm) or wider clearance at the back of the printer. Keep 17.7 in. (45 cm) or wider space free above the unit as well. If this

space is not secured, you will have to move peripherals or the printer when making a repair.

 When installing the printer, place a level gage on the top surface of the platen to make adjustments so that the main unit is

set horizontally.

Ink bottle

9 L

18 L

Pretreatment

20 kg (44 lb)

200 kg (440 lb)

3) Pickup the Lithium Battery (1) to the direction of the arrow.

(1)

Note based on California law (USA) on the

use and handling of Perchlorate

This product contains a CR Coin Lithium Battery

which contains Perchlorate Material – special

handling may apply.

See

http://www.dtsc.ca.gov/hazardouswaste/perchlorate.

 The following environmental requirements should be met:

Environment

Temperature

0°C (32°F) to

Humidity (%)

40°C (104°F)

Working

10°C (50°F) to

Environment

35°C (95°F)

Recommended

18°C (64.4°F) to

Print Environment

30°C (86°F)

Electrical

Power

Requirements

Single-phase

―

200-240 V,

X1016

50/60 Hz

: Environmental range where the printer can be operated.

: Environmental range where sufficient printing quality can

be secured.

Transporting the printer

There is a label on the back of the

Pretreatment

printer that indicates the insertion slot.

5 kg (11 lb)

X1057

Refilling the ink and cleaning solution

Turn ON the power of the printer and perform the operation

while the printer is in Standby mode.

Be sure to wear a pair of plastic gloves and protective

glasses while refilling the ink.

Agitate the white ink before refilling.

IMPORTANT

For details, refer to the Instruction Manual.

-> [Ink refill] -> Select the ink color and cleaning

solution you want to refill ->

Insert the IC stick of the same color as the ink to refill ->

Maintenance list

To maintain the printing quality and use the printer for a longer time, the following maintenance is needed.

For details, refer to the Instruction Manual.

Maintenance timing

Before printing

When an error /

warning is displayed

When the printer

becomes dirty

Humidity

20 % to 85 %

(no condensation)

35% to 85 %

(no condensation)

Power

Consumptions

5 A max.

*Please note that the contents of this manual may differ slightly from the actual product purchased as a result of product

improvements.

1-5, Kitajizoyama, Noda-cho, Kariya 448-0803, Japan.

This is the original instructions.

X1054

The printer has a dimension of 73.6 in. (width) × 75.6 in.

(depth) × 57.5 in. (height) (187 cm (width) × 192 cm

(depth) × 146 cm (height)). The main unit weighs 730 kg

(1609 lb). Transporting and setting up of the printer

should be held by at least three persons in the proper

way. Otherwise, the printer may topple over and cause

injury.

During transportation, be careful not to get your feet

caught in the frame, casters, or adjusters under the

printer. Also, check the forward direction and be careful

not to get caught between obstacles and this printer.

Otherwise, the operator may get injured.

X1034

Refill the ink and cleaning solution.

CAUTION

IMPORTANT

Follow the instructions on the screen.

IMPORTANT

Description

Print out of the nozzle check pattern (checking on the print heads)

Confirmation and disposal of waste ink

Confirmation and disposal of waste water

Refilling the ink

Refilling the cleaning solution

Cleaning the nozzle guard and suction cap

Replacing the wiper, flushing foam, cap foam, and carriage foam

Replacing the mist fan filter

Head cleaning

White ink circulation

Cleaning the internal area of printer

Replacing the platen sheet

https://www.brother.com/

X1035

CAUTION

When refilling ink or cleaning solution,

make sure the surface of the ink or

cleaning solution does not exceed the

scale line above 6. For white ink or

cleaning solution, refill it until the surface

exceeds the scale line below 6. For color

ink, refill it until the surface exceeds the

scale line below 4.

Be sure to close the tank lids once you

have refilled the ink and cleaning solution.

To store a cock after use, wipe off ink with

a waste cloth and seal it in a plastic bag.

Do not use a non-standard funnel. Use

the provided cock. Otherwise, ink may be

contaminated or deteriorated, possibly

damaging the printer.

Error /

Warning display

―

○

―

GT60NB

SC5083-101 EN

2022.01.F(1)