Brother GTX600NB Посібник з техніки безпеки - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник з техніки безпеки для Принтер Brother GTX600NB. Brother GTX600NB 2 сторінки. Garment pra inter
Також для Brother GTX600NB: Посібник з налаштування (45 сторінок)

3. Warning labels
2
1
2
6
Waste ink tank
Waste water
tank
6
Cleaning solution bottle
9 L
Cleaning solution bottle
18 L
1                                          4                                6 
 
3                                          5                                7
 
 
 
<When you dispose of the machine>
Required Tools
Phillips screwdriver: M3 to M5
Disassembling
1) Remove the Cover of BACK SIDE bottom center.
2) Remove the Lithium Battery (1) by pulling out the holder
in the direction of the arrow.
(1)
Checking the installation site
1
17.7 in. (45 cm) or more
31.5 in. (80 cm)
or more
15.7 in. (40 cm)
or more
31.5 in. (80 cm)
or more
31.5 in. (80 cm)
or more
129.5 in. (329 cm)
116.5 in. (296 cm)
or more
or more
 When installing the printer, avoid any place that presents direct sunlight or a large amount of dust.
 The size is 73.6 in. (width) x 75.6 in. (depth) x 57.5 in. (height) (187 cm (width) x 192 cm (depth) x 146 cm (height)). The
main unit weighs 730 kg (1609 lb).
 Do not use an extension cable.
 Keep a minimum workspace of 31.5 in. (80 cm) in front and on the left and right sides of the printer. Also, keep 15.7 in. (40
cm) or wider clearance at the back of the printer. Keep 17.7 in. (45 cm) or wider space free above the unit as well. If this
space is not secured, you will have to move peripherals or the printer when making a repair.
 When installing the printer, place a level gage on the top surface of the platen to make adjustments so that the main unit is
set horizontally.
4
5
3
6
6
6
Ink bottle
Ink bottle
9 L
18 L
6
6
Pretreatment
Pretreatment
20 kg (44 lb)
200 kg (440 lb)
3) Pickup the Lithium Battery (1) to the direction of the arrow.
(1)
Note based on California law (USA) on the
use and handling of Perchlorate
This product contains a CR Coin Lithium Battery
which contains Perchlorate Material – special
handling may apply.
See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
 The following environmental requirements should be met:
Environment
Temperature
0°C (32°F) to
Humidity (%)
40°C (104°F)
Working
10°C (50°F) to
*1
Environment
35°C (95°F)
Recommended
18°C (64.4°F) to
*2
Print Environment
30°C (86°F)
Electrical
Power
Requirements
Single-phase
200-240 V,
X1016
50/60 Hz
1
*
: Environmental range where the printer can be operated.
2
*
: Environmental range where sufficient printing quality can
be secured.
Transporting the printer
2
6
There is a label on the back of the
Pretreatment
printer that indicates the insertion slot.
5 kg (11 lb)
7
X1057
Refilling the ink and cleaning solution
3
Turn ON the power of the printer and perform the operation
while the printer is in Standby mode.
Be sure to wear a pair of plastic gloves and protective
glasses while refilling the ink.
Agitate the white ink before refilling.
IMPORTANT
For details, refer to the Instruction Manual.
1)
-> [Ink refill] -> Select the ink color and cleaning
solution you want to refill ->
2)
Insert the IC stick of the same color as the ink to refill ->
Maintenance list
To maintain the printing quality and use the printer for a longer time, the following maintenance is needed.
For details, refer to the Instruction Manual.
Maintenance timing
Before printing
When an error /
warning is displayed
When the printer
becomes dirty
Humidity
20 % to 85 %
(no condensation)
35% to 85 %
(no condensation)
Power
Consumptions
5 A max.
*Please note that the contents of this manual may differ slightly from the actual product purchased as a result of product
improvements.
1-5, Kitajizoyama, Noda-cho, Kariya 448-0803, Japan.
© 2021-2022 Brother Industries, Ltd. All Rights Reserved.
This is the original instructions.
X1054
The printer has a dimension of 73.6 in. (width) × 75.6 in.
(depth) × 57.5 in. (height) (187 cm (width) × 192 cm
(depth) × 146 cm (height)). The main unit weighs 730 kg
(1609 lb). Transporting and setting up of the printer
should be held by at least three persons in the proper
way. Otherwise, the printer may topple over and cause
injury.
During transportation, be careful not to get your feet
caught in the frame, casters, or adjusters under the
printer. Also, check the forward direction and be careful
not to get caught between obstacles and this printer.
Otherwise, the operator may get injured.
X1034
3)
Refill the ink and cleaning solution.
CAUTION
IMPORTANT
4)
Follow the instructions on the screen.
IMPORTANT
Description
Print out of the nozzle check pattern (checking on the print heads)
Confirmation and disposal of waste ink
Confirmation and disposal of waste water
Refilling the ink
Refilling the cleaning solution
Cleaning the nozzle guard and suction cap
Replacing the wiper, flushing foam, cap foam, and carriage foam
Replacing the mist fan filter
Head cleaning
White ink circulation
Cleaning the internal area of printer
Replacing the platen sheet
https://www.brother.com/
X1035
CAUTION
When refilling ink or cleaning solution,
make sure the surface of the ink or
cleaning solution does not exceed the
scale line above 6. For white ink or
cleaning solution, refill it until the surface
exceeds the scale line below 6. For color
ink, refill it until the surface exceeds the
scale line below 4.
Be sure to close the tank lids once you
have refilled the ink and cleaning solution.
To store a cock after use, wipe off ink with
a waste cloth and seal it in a plastic bag.
Do not use a non-standard funnel. Use
the provided cock. Otherwise, ink may be
contaminated or deteriorated, possibly
damaging the printer.
Error /
Warning display
GT60NB
SC5083-101 EN
2022.01.F(1)