Dexter Laundry 80LB CAPACITY COMPUTER CONTROL OPL WASHER T1200 Instrukcja instalacji i obsługi - Strona 15

Przeglądaj online lub pobierz pdf Instrukcja instalacji i obsługi dla Spryskiwacz Dexter Laundry 80LB CAPACITY COMPUTER CONTROL OPL WASHER T1200. Dexter Laundry 80LB CAPACITY COMPUTER CONTROL OPL WASHER T1200 18 stron. 80lb capacity computer control opl washer

Drukuj stronę

WASHER ERROR CODES

Fault #
Description
(F #)
1
The door failed to close and lock or the door
failed to remain locked after three tries of
latching the door and starting during the cycle.
2
The washer tub does not fill with water within 7
minutes. The wash cycle will continue. The F 2
will flash three times, then wait for 30 seconds.
The error will clear at the end of the cycle.
3
Memory error in controller.
4
Washer controller communication error
5
Pressure Switch error ( only OPL )- when the
high level sensor indicates full but the lower one
indicates empty. The wash cycle will continue.
The F 5 will flash three times, then wait for 30
seconds. The error will clear at the end of the
cycle.
6
Wrong washer size for drive type.
7
Wrong size drive installed
8
The washer tub does not empty within 7
minutes. The wash cycle will continue. The F 8
will flash three times, then wait for 30 seconds.
The error will clear at the end of the cycle.
9
The washer tub does not reach the spin target
frequency within 200 seconds. The wash cycle
will continue. The F 9 will flash three times,
then wait for 30 seconds. The error will clear at
the end of the cycle.
10
After a spin the washer tub does not stop within
150 seconds.
Turn off the power to the washer. Check wire connections to door /lock switches. Check wire
connections from switches to controller. If necessary the door lock mechanism should be
adjusted by a qualified person. Turn on the power to the washer. (See Note)
Turn of the power to the washer. Check the operation of the water valves. Check the
incoming water pressure. Check for blocked or restricted water flow. Check to ensure the
drain valve is functioning properly. Turn on the power to the washer. (See Note)
Turn off the power to the washer. Wait one minute. Turn power back on to the washer. If the
problem returns, clear the fault with the Palm. If the problem returns again, replace the
washer controller.
Turn off the power to the washer. Wait one minute. Turn power back on to the washer. If the
problem returns, replace the washer controller.
Turn off the power to the washer. Replace the pressure switch. Turn on power to the washer.
(See Note)
Turn off the power to the washer. Check to ensure all the harnesses are properly connected
to the controller. Check to ensure the drive horsepower is proper for this size of washer. Turn
on power to the washer. (See Note) If problem reappears, contact your Dexter
representative.
Turn off the power to the washer. Check to ensure all the harnesses are properly connected to
the controller. Check to ensure the drive horsepower is proper for this size of washer.
Contact your Dexter representative.
Turn off the power to the washer. Check to ensure the drain valve is operating properly.
Check to ensure the pressure switch tube is clear of blockage. Check to ensure the pressure
switch is operating proper. Correct any located problems. Turn on power to the washer.
(See Note)
Turn off the power to the washer. Inspect the washer to ensure the tub spins freely. If
restricted, then clear the blockage. Test washer. If tub spins freely, the drive needs to be
replaced.
Turn off the power to the washer. Inspect the braking resistors and the connecting wiring to
the drive braking resistors mounted in the top of the washer. If the resistors and wiring is
correct, then replace the drive.
Customer Action