Billi Quadra 440 Instrukcja instalacji - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Armatura kuchenna i łazienkowa Billi Quadra 440. Billi Quadra 440 8 stron. Tower dispenser
Również dla Billi Quadra 440: Instrukcja instalacji (12 strony)
Drukuj stronę
Installing the dispenser.
XL, XT, XR.
IMPORTANT: This Billi appliance is to be installed by a licensed trades person in accordance with
AS/NZS 3500.1 and AS/NZ 3500.2 and in compliance with applicable state regulatory requirements.
For correct operation of this appliance, it is essential to observe the manufacturer's instructions.
1. Install Dispenser Assembly
Determine position of dispenser mounting
hole in sinktop or benchtop. Dispenser base
template (Diagram 4) may be cut out and
used to assist in correct positioning. Refer to
Diagram 2 for clearances allowed. Hole size
required is ø32mm.
—Stainless Steel Sinktop
A suitable 32mm hole punch (Part no:
857901) is available as an accessory from
Billi Pty Ltd. If possible, cut hole with die
mounted below the sinktop surface so that
burr is pulled downwards. Alternatively,
remove burr and radius edge of hole with
fine file. This allows barbed dispenser mount
to slide smoothly into mounting hole.
—Timber/Laminate Benchtop
Maximum benchtop thickness is 50mm.
Cut 32mm hole in appropriate position*.
When drilling through a particle board
bench top, take care to avoid a large chip
breaking away as drill breaks through
underside surface. We recommend drilling
a small pilot hole through benchtop, partially
drilling the 32mm hole from underneath and
then completing drilling the hole from above.
The large 30mm washer supplied may be
used to secure barb where underside particle
board bench top has chipped away.
* For granite or marble bench tops
we recommend you use a certified
stone mason to pre-drill the hole.
2. Activate Dispenser Swivel Feature
To activate the swivel feature of your
dispenser, you will need to remove the
locking piece from the dispenser base.
Simply push out the piece as show in
Diagram 5. This will allow the tap to
move 45 degrees to the left and right.
3. Fit Dispenser Base
a. Cut a 32mm hole in sinktop or benchtop.
Remove burr if protruding upwards.
b. Push barbed mounting shaft through
mount hole.
c. Insert barb locking bush as shown in
Diagram 6. Finger tighten nut.
d. Ensure barb is centred in mount hole
before tightening. Check position of base
ring and gasket.
e. Moderately tighten locking nut using
multigrips or spanner. Take care to avoid
overtightening nut which may break the
plastic threaded shaft.
f.
Place large D washer over thread as
shown in Diagram 7.
g. Cut off excess threaded shaft with a
hacksaw, using washer as a cutting guide.
IMPORTANT: Remove burrs and check internal
bore is completely smooth.
4. Fit Dispenser Head Assembly
a. Feed dispenser tubing and loom through
centre hole in the following order:
i. Dispenser power cord.
ii. Silicone tubes
b. Gently pull hoses from under the bench
top, do not attempt to force tubing through
with a pointed object as silicone tube is
easily punctured. Check tubing is not
kinked or twisted.
c. Turn dispenser head assembly to
approximately 60° from the straight
ahead position of dispenser base.
Slide head assembly onto base assembly
whilst gently pulling tubing downwards
from underneath to prevent tubing
bunching and kinking. Mounting lugs
will pass nut and slide down the 3
grooves on the swivel bearing.
d. Once fully down, turn dispenser to
straight ahead position. Fit chrome
plated M4 retaining screw to lower
rear threaded hole and tighten using the
allen key supplied. If swivel feature is
activated, check dispenser now swivels
smoothly 45° in each direction.
dispenser base
template
Locking Nut
Base Casting
Ensure burr
is removed
& edge has
a radius
Barbed
Mounting
Shaft
Barb locking bush in position
Remove burrs after cutting and
ensure internal bore is smooth
Cut off
excess
thread
D washer
Silicone
tubing
Diagram 4
Diagram 5
Swivel
Bearing
Gasket
D Washer
required
Diagram 6
Alloy locking
bush
Diagram 7
Diagram 8
3
3