Dell DX6000 Instrukcja konfiguracji i ustawień - Strona 15

Przeglądaj online lub pobierz pdf Instrukcja konfiguracji i ustawień dla Przechowywanie Dell DX6000. Dell DX6000 43 stron. Rack installation instructions — static rails
Również dla Dell DX6000: Podręcznik uzupełniający (4 strony), Instrukcja instalacji sprzętu (2 strony), Podręcznik użytkownika (46 strony), Instrukcja instalacji i konfiguracji (35 strony), Podręcznik dla początkujących (28 strony), Zawiadomienie (28 strony), Zawiadomienie (20 strony), Przegląd (19 strony), Podręcznik konfiguracji (9 strony), Podręcznik konfiguracji (9 strony), Uwaga dotycząca wydania (8 strony), Podręcznik referencyjny (12 strony), Podręcznik konfiguracji (7 strony), Uwaga dotycząca wydania (6 strony), Uwaga dotycząca wydania (5 strony), Informacje o wersji (5 strony), Instrukcje instalacji (2 strony), Instrukcje instalacji (2 strony)

Chapter 4. Installation

DX Content Router installs as a service on a standard server, using standard Linux installation

and package management utilities as outlined in the sections below. Note, that if running DX

Content Router from a Cluster Services Node (CSN), the required infrastructure setup, installation

and configuration are performed automatically as part of CSN configuration so the steps below

are not necessary or even supported in some cases. Please reference the CSN Installation and

Configuration Guide for information on installing and configuring DX Content Router on the CSN.

DX Content Router has been developed and tested with 64-bit Red Hat Enterprise Linux (RHEL)

version 5.5. Other RHEL versions or Linux distributions are not currently supported. Subsequent

installation instructions will assume an existing RHEL installation.

DX Content Router has dependencies on Python 2.5, Python Setuptools 0.6c9, and Twisted 8.2.0,

which are not available as standard RPM packages under RHEL 5.5 but are included in the DX

Content Router installation package and will be unzipped into the same location as the DX Content

Router rpm (see the 'Installing Services' section below). If installing on a Cluster Services Node

(CSN), these RPMs will already be installed. If installing without a CSN, you may need to manually

install the packages using the commands shown below (in this order):

rpm -ivh caringo-3rdparty-Python-2.5.4-x86_64.rpm

rpm -ivh caringo-3rdparty-setuptools-0.6c9-x86_64.rpm

rpm -ivh caringo-3rdparty-Twisted-8.2.0-x86_64.rpm

The DX Storage system has been designed to work within standard TCP/IP networking

environments. This is achieved through the use of widely supported network services and protocols.

4.1.3.1. Required Communications

A DX Content Router node must be able to initiate TCP connections with all nodes in a DX Storage

cluster through the designated access port. This is typically HTTP port 80, but it is configurable by

the administrator.

Internally, DX Content Router nodes must be able to communicate with each DX Storage node

via UDP on port 7000 and through IP multicasting. The multicast address must be unique for each

cluster and is configurable by the administrator. Multicast communication is only necessary between

the DX Content Router nodes and the DX Storage nodes.

All nodes in the DX Storage cluster, including DX Content Router nodes must reside within the

same IP subnet.

4.1.3.2. Bandwidth Requirements

The expected transfer rate for two clusters communicating over a wide area network can be roughly

calculated by dividing the minimum effective bandwidth available (ex: 512 kbps) by the number

of volumes in the target cluster. By default, DX Storage requires a minimum transfer rate of 1000

bytes/sec before timing out connections. The transfer rate is not checked for the initial 20 minutes to

provide some latitude for network variability. Administrators anticipating a transfer rate below 1000

Version 2.2

December 2010