Bionaire BEF6300 Instrukcja obsługi - Strona 3
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Kominek wewnętrzny Bionaire BEF6300. Bionaire BEF6300 4 stron. Electric fireplace heater
Również dla Bionaire BEF6300: Instrukcja obsługi (8 strony)
Drukuj stronę
U.K. and IRELAND
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
the following:
1. Before connecting the heater, check that
the voltage indicated on the rating plate
corresponds to the main voltage in your
home/office.
2. WARNING: In order to avoid overheating,
do not cover the heater (
).
3. DO NOT position the heater directly under
a power socket.
4. DO NOT use this heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged, it
must be replaced by the manufacturer or its
service agent or similarly qualified person in
order to avoid hazard. Should the product
suffer damage or breakdown, it must be
returned to the manufacturer or their service
agent.
6. Under the environment with electrical fast
transient, the product may malfunction and
require user to reset the product.
7. DO NOT use this heater with a
programmer, timer, separate remote-
control system or any other device that
switches the heater on automatically, since
a fire risk exists if the heater is covered or
positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT position where it can be touched
by children, especially the very young.
10. DO NOT use this heater outdoors.
11. Allow a safe area around the heater away
from furniture or other objects; at least 50 cm
from the top and sides and 200 cm at the
front.
12. DO NOT use this heater when it is lying on
its side.
13. DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using
inflammable glue or solvent (e.g. when
gluing or varnishing parquet floors, PVC
etc.).
14. DO NOT insert any objects into the heater.
15. Keep the mains cord at a safe distance
from the main body of the heater.
16. If overheating should occur, the built-in
overheating safety device will switch off
the heater.
17. DO NOT place the cord under a rug.
18. The heater is to be installed so that
switches and other controls cannot be
touched by a person in the bath or shower.
19. Avoid the use of an extension cord
because it may cause the heater to
overheat.
20. CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied
through an external switching device, such
as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
21. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
22. (
) The remote control contains a magnet
to help affix the control to the metal main
unit when not in use. Please only place
the remote control on the unit where the
remote control home is marked (H).
DESCRIPTIONS
(See Fig. 1, 2, 3, 4, & 6)
A. Glass panel
B. Pebbles (changeable)
C. Light bulb access panel (contains G9 type
40W max bulb)
D. Main housing
E. Fixed unit mounting brackets
F. Heat vents
G. Control panel
H. Remote control home
I. Feet x 2 (removable)
J. Mode control
K. Flame intensity button
L. ON/OFF switch (main unit only)
M. Thumb screws x4
N. Securing bottom bracket (BEF6400)
O. ON/OFF button remote control
ASSEMBLY INSTRUCTIONS
(See Fig. 1–6)
Carefully remove all parts and make sure that
they are all present. Ref. to Figs.1-6.
Installing Batteries into the Remote:
Before operation, insert 2 AAA batteries (not
supplied) into the back of the remote control:
• DO NOT mix old and new batteries
2
• DO NOT mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium)
batteries
The remote control for this unit has the
capability of operating all control panel functions
except the mechanical ON/OFF switch (L).
Please note this remote will not work through
walls (See Fig. 3).
Stand Assembly (See Fig. 6):
For floor use attach the two feet assemblies
(I) to the fireplace heater using the 4 thumb
screws (M) provided. Gently lay the main
housing (D) horizontally down without the glass
panel attached. Line up each feet assembly
using the metal guides and then screw in
two thumb screws (M) into the corresponding
holes. Place unit upright, add the pebbles (B)
and then attach the glass panel by lining up the
glass panel metal guides with the main housing
panel pins. For wall mounting see Wall Mount
Installation below.
Wall Mount Installation
(See Fig. 4 & 5):
This product (BEF6300) weighs 15 kg
(BEF6400: 16.3 kg). Do not install alone. The
following procedure is for a dry wall installation
using the provided hardware.
Note: If installing on a different type of wall (i.e
cavity wall) or using different hardware please
consult a professional for advice on the correct
way to install the unit.
IMPORTANT: Before drilling into any wall
ensure no electrical cables are present in the
area. Make sure you allow the correct spacing
on all four sides of the unit (See figure 5).
1. Turn unit off and disconnect the unit if in
use.
2. Remove front glass and pebbles if
installed.
3. Remove feet assemblies from main
housing by unscrewing the thumb screws.
4. Decide on the position where the
electric fireplace will hang on the wall.
REMEMBER not to position directly above
the power socket and at least 1m away
from any objects on all sides (reference
Fig. 5).
5. Mark on the wall the points between the
centre of the holes on the fixed unit rear
mounting brackets (E) making sure the
points line up and are level (reference
Fig. 4)
6. Drill into the wall using an 8mm drill bit two
holes on the marked points so that you can
fit the appropriate wall plugs.
7. Screw in two 4 x 35mm screws into the
wall plugs, leaving 10mm of the screws out
of the wall.
8. Hang the main body of the unit onto the
two exposed screws by lining up the rear
mounting brackets' holes.
9. BEF6400: Place the securing bottom
bracket (N) into the rear of the unit and
then use one 4x35mm screw to secure the
bracket and unit to the main wall.
10. Add pebbles to the unit, then place the
glass panel onto the unit by lining up the
glass panel guides with the main housing
pins (located on the side of the housing)
and make sure the unit is secure.
11. Unit is now ready to be turned on and
operated.
OPERATING INSTRUCTIONS
• There may be an odor coming from the
heater the first time you use it. This is normal
during the break-in period or after long term
storage. Make sure the heater is in a well
ventilated area and continue running it until
the smell goes away.
• You may hear a popping or crackling sound
as the heater heats up. This is normal and
safe operation.
• The Fireplace Heater can be operated by
using the remote control (Fig. 3) or the
control panel (Fig. 2) located on the side of
the unit.
• Place the heater on a firm, level surface or
mount on wall.
• Avoid overloading your circuit by not using
other high wattage appliances in the same
outlet.
POWER ON/OFF
1. Turn the main ON/OFF switch (L) on the
—
main unit to the ON (
) position.
2. Either press the mode control (J) or the
flame intensity button (K) on the main unit
or remote control to start the operation of
the unit.
3. If for any reason you would like to turn the
unit off press the mode button or flame
intensity button on the control panel or the
ON/OFF Button (O) on the remote so that
no function is heard or visible and then
switch the ON/OFF switch on the main unit
to the OFF ( ) position.
MODE SETTINGS
Once the main ON/OFF switch has been
switched to ON, press the mode control button
(J) on the panel or remote control:
3