Olympus BH2-CH Substage Montaż - Strona 3

Przeglądaj online lub pobierz pdf Montaż dla Mikroskop Olympus BH2-CH Substage. Olympus BH2-CH Substage 26 stron.

Table of Figures

Figure 1 - Head of a typical JIS screw ..................................................................................................................................... 6

Figure 2 - Adjust condenser height until screw is visible ....................................................................................................... 7

Figure 3 - Unscrew and remove the slotted stop screw ........................................................................................................ 7

Figure 4 - Remove the condenser slide assembly .................................................................................................................. 8

Figure 5 - Remove the condenser-lock thumbscrew ............................................................................................................. 8

Figure 6 - Remove the centering thumbscrews ..................................................................................................................... 8

Figure 7 - The condenser-slide assembly (bottom view) ....................................................................................................... 8

Figure 8 - Remove screws securing the slip plates ................................................................................................................. 8

Figure 9 - Remove the three slip plates ................................................................................................................................. 8

Figure 10 - Look for shim washers under the slip plates ........................................................................................................ 9

Figure 11 - Remove any brass shim washers ......................................................................................................................... 9

Figure 12 - Depress the centering plunger ............................................................................................................................. 9

Figure 13 - Separate centering yoke from support yoke ....................................................................................................... 9

Figure 14 - The support yoke on the condenser slide ............................................................................................................ 9

Figure 15 - The centering yoke ............................................................................................................................................... 9

Figure 16 - Remove screws and washers securing rack ....................................................................................................... 10

Figure 17 - Remove the condenser-height rack ................................................................................................................... 10

Figure 18 - Brass shim for the condenser-height rack ......................................................................................................... 10

Figure 19 - Remove brass shim for condenser-height rack .................................................................................................. 10

Figure 20 - Loosen set screw while holding the stop pin ..................................................................................................... 10

Figure 21 - Remove the loose stop pin from the bore ......................................................................................................... 10

Figure 22 - Remove the stop-pin spring from the slide ....................................................................................................... 11

Figure 23 - Back out the stop-pin set screw from the slide ................................................................................................. 11

Figure 24 - Test the fit of the stop pin in the bore ............................................................................................................... 11

Figure 25 - Clean any debris or burring from the bore ........................................................................................................ 11

Figure 26 - Reinstall the stop-pin spring into the bore ........................................................................................................ 11

Figure 27 - Reinstall the stop pin into the bore ................................................................................................................... 11

Figure 28 - Tighten set screw to lock the stop pin ............................................................................................................... 12

Figure 29 - Test centering plunger for freedom of motion .................................................................................................. 12

Figure 30 - Loosen the plunger-retaining screw .................................................................................................................. 12

Figure 31 - Remove the plunger-retaining screw ................................................................................................................. 12

Figure 32 - Remove the plunger-extension spring ............................................................................................................... 12

Figure 33 - Press centering plunger out the back of bore .................................................................................................... 12

Figure 34 - Remove centering plunger from the bore ......................................................................................................... 13

Figure 35 - Clean grease from bore and dovetail slide ........................................................................................................ 13

Figure 36 - Apply grease to the centering-plunger bore ...................................................................................................... 13

Figure 37 - Reinstall plunger and c-clip into bore ................................................................................................................ 13

Figure 38 - Reinstall plunger-extension spring into bore ..................................................................................................... 13

Figure 39 - Reinstall the plunger-retaining screw ................................................................................................................ 13

Figure 40 - Tighten the plunger-retaining screw .................................................................................................................. 14

Figure 41 - Head of retaining screw must be recessed ........................................................................................................ 14

Figure 42 - Reinstall brass shim for condenser-height rack ................................................................................................. 14

Figure 43 - Reinstall screws for the condenser-height rack ................................................................................................. 14

Figure 44 - Tighten screws for the condenser-height rack................................................................................................... 14

Figure 45 - Parts for the condenser-centering mechanism.................................................................................................. 14

Figure 46 - Lightly grease the underside of centering yoke ................................................................................................. 15

Figure 47 - Reinstall centering yoke into support yoke ....................................................................................................... 15

Figure 48 - Reinstall any brass shim washers ....................................................................................................................... 15

Figure 49 - Apply grease to the three slip bosses ................................................................................................................ 15

Figure 50 - Reinstall slip plates onto the slip bosses ............................................................................................................ 15

Figure 51 - Reinstall screws to secure the slip plates ........................................................................................................... 15

Complete Teardown, Cleaning/Lubrication, and Reassembly of the Olympus BH2-CH Substage Assembly

Revision 1

Page 3 of 26