Fibar Group FGS-212 Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Przełącznik Fibar Group FGS-212. Fibar Group FGS-212 2 stron. Relay switch

Drukuj stronę

ENG

Technical Information

• Controlled by FIBARO system devices or any Z-Wave controller.

•

Electronic switch is a remote control unit.

• Microprocessor control.

• Active element: electromagnetic, micro-gap relay switch.

• The device may be operated by momentary and toggle

push-buttons.

•

To be installed in wall switch boxes of dimensions allowing for

installation, conforming to provisions of applicable regulations.

I General information about Fibaro system

FIBARO is a wireless system, based on Z-Wave technology.

FIBARO provides many advantages when compared to similar

systems. In general, radio systems create a direct connection

between the receiver and transmitter. But the radio signal is

weakened by various obstacles located on its path (apartment

OPERATING MANUAL

walls, furniture, etc.) and in extreme cases it fails to transfer

required data. The advantage of FIBARO system is that its devices

RELAY SWITCH

apart from being transmitters and receivers of signals, they are also

a signal "duplicators". When a direct connection path between the

FGS-212-EN-A-v1.1

transmitter and the receiver can not be established, the connection

may be achieved through other intermediate devices.

FIBARO is a bi-directional wireless system. It means that the signal

is not only sent to the receivers but also the receivers send the

confirmation of its reception. This operation confirms their status so

to check whether they are active. Safety of the FIBARO system

Remotely Controlled Relay Switch of Fibaro System is designed to

transmission is comparable to the safety of transmission in data bus

operate in a wall switch box or in locations where the control of an

wired systems.

electric device (up to 2.5kW) is needed.

FIBARO operates in the free band for data transmission. The

It is also possible to send a signal to any system that is to be

frequency depends on radio regulations in individual country . Each

integrated with Fibaro system.

FIBARO network has its own unique network identification number

(home ID), which is why it is possible to co-operate two or more

Specifications

independent systems in a single building without any interference.

Although Z-Wave is quite new technology, it has already become

Power supply:

110 - 240V ~

recognizable and officially binding standard, similarly to Wi-Fi.

50 - 60Hz

Many manufacturers in various industries offer solutions based on

Z-Wave technology, guaranteeing their compatibility. This means

Power consumption:

to 0,8W

that the system is open and it may be extended in the future. Find

more information at www.fibaro.com.

Operational temperature:

0 - 35°C

FIBARO generates a dynamic network structure. After FIBARO

Dimensions (L x W x H):

42,50 x 38,25 x 20,30 mm

system is switched on, the location of its individual components is

automatically updated in real-time through status confirmation

For installation in boxes:

Ø ≥ 50mm

signals received from devices operating in a "mesh" network.

Rated load current:

10A for resistive load*

The In-Wall Relay Switch is hereinafter referred to as Fibaro

Switch. It is designed to switch on/off devices connected to its

Overcurrent protection:

required external 10A circuit

terminals using radio waves, controllers and a push button directly

breaker

connected to Fibaro Switch.

Active element:

micro-gap relay switch μ

II Assembling Fibaro Switch

Device control:

remotely - radio waves

directly - push buttons

Radio protocol:

Z-Wave

Radio signal power:

1mW

Radio Frequency:

868,4 MHz EU;

908,4 MHz US;

921,4 MHz ANZ;

869,0 MHz RU;

865,2 MHz IN;

Range:

up to 50 m outdoors

up to 30 m indoors

(depending on building materials)

Comply with EU directives:

RoHS 2011/65/EU

RED 2014/53/EU

1. Before installation ensure that the voltage supply is

disconnected.

2. Connect Fibaro switch as shown on the diagram.

3. Place the switch in the switch box.

4. Arrange the antenna (tips are presented further).

Single switch - mains electricity power connection

Double switch - mains electricity power connection

Fig.1 Wiring diagrams for Fibaro Switch.

NOTES FOR THE DIAGRAM:

N - terminal for neutral lead

L - terminal for live lead

IN - input terminal for load power supply

Q - output terminal of the load

CAUTION

S2 - terminal for key no. 2

Read this manual before attempting to install

S1 – terminal for key no. 1 (has the option of entering the device in

the device! Failure to observe recommendations

learning mode)

included in this manual may be dangerous or cause

B- service button (used to add or remove a device from the system)

a violation of the law. The manufacturer, Fibar

Group S.A. will not be held responsible for any loss

or damage resulting from not following the

instructions of operating manual.

CAUTION

Product must be installed on a 10A line.

DANGER

Danger of electrocution! Electronic switch is

designed to operate in electrical home installation.

Faulty connection or use may result in fire or electric

shock.

DANGER

Danger of electrocution! All works on the device

Fig.2 Installation of Fibaro Relay Switch in wall switch box.

may be performed only by a qualified and licensed

electrician. Observe national regulations.

CAUTION

The switch box must be compliant with the relevant

DANGER

national safety standards and it's depth should not

be less than 60mm.

Danger of electrocution! Even when the device is

turned off, voltage may be present at its terminals.

Any

works

introducing

changes

into

the

CAUTION

configuration of connections or the load must be

The device is designed for installation in wall

always performed with disconnected voltage

(disable the fuse).

switch boxes and can work only with the electrical

connectors compliant with the relevant safety

standards.

CAUTION

Do not connect the device to loads exceeding

NOTE

recommended

values.

Connect

only

Durability of the device depends on applied load.

For resistive load (light bulbs, etc.) and 6,5A current

accordance with the diagram presented in the

per channel, the durability exceeds 200 000

manual. Improper connections may be dangerous.

switches.

TIPS FOR ARRANGING THE ANTENNA:

Locate the antenna as far from metal elements as

possible (connecting wires, bracket rings, etc.) in

order to prevent interferences.

Metal surfaces in the direct vicinity of the antenna

(e.g. flush mounted metal boxes, metal door

frames) may impair signal reception!

Do not cut or shorten the antenna - its length is

perfectly matched to the band in which the system

operates.

NOTE

It should be noted that only the push-button

connected to S1 terminal and service push-button

S1 S2

B enables "learning" mode (Include/ Exclude).

SWITCH

DICTIONARY:

• Adding (Inclusion) - Z-Wave device learning mode, allowing to

add the device to existing Z-Wave network.

• Removing (Exclusion) - Z-Wave device learning mode, allowing

to remove the device from existing Z-Wave network.

• Association (linking devices) - direct control of other devices

within the Z-Wave system network.

• Multi-channel association - controlling other multi-channel

devices within the Z-Wave network.

III Activating Fibaro Switch

1. Installing the Fibaro Switch

S1 S2

STEP 1

Connect the device in accordance with the wiring diagram

SWITCH

presented in Figure 1. Switch on the mains voltage.

[Adding/Removing] Fibaro Switch [to/from] Z-wave network

STEP 2

Fibaro Switch must be placed within the range of Home Center

controller, as adding mode requires direct communication with the

controller.

STEP 3

Find key no. 1 which allows to switch circuit 1 on, in accordance

with the diagram

STEP 4

Set the Home Center controller in add/remove mode (see the

controller's manual)

STEP 5

Add Fibaro Switch to the network by pushing three times key no. 1

or push-button B located inside the housing of the device. For

toggle switch perform 3 position changes.

During the installation it is recommended to use a

momentary key connected to S1.

STEP 6

The controller indicates when the device is correctly added to the

network, (see the manual of Home Center controller).

CAUTION

Fibaro Switch cancels the "learning" mode after

key no. 1 is pressed once. Therefore, pressing key

no. 1 four times will not add the devices to the

network. The same applies to push-button B.

CAUTION

Fibaro Switch is set by default to operate with

toggle switches. While adding Fibaro Switch to the

network with toggle switches, ensure that all switch

contacts are open (off), because closing them

results in activating the push-button and this will

prevent adding the device to the network.

2. Resetting Fibaro Switch

Fibaro Switch provides two methods for resetting.

Method I : Reset by removing Fibaro Switch from the existing

Z-Wave network. The device may be removed using the controller

that has the ability to include/exclude devices from/to Z-Wave

network (see the manual of controller).

Method II : Reset by holding B button for 3 sec. after connecting

mains voltage to the Switch

3. Controlling Fibaro Switch by momentary or toggle

V Configuration

switches.

The following settings are available in the Fibaro interface as

Momentary switch (after releasing the push-button a spring

simple options that may be chosen by selecting the appropria-

automatically pushes back and disconnects the button)

box.

- Turning on/off circuit 1 or 2 - briefly press the push-button

In order to configure Fibaro Switch (using the Home Center

corresponding to a chosen circuit (see diagram).

controller), go to device options by clicking the following icon:

Toggle switch (operates as a two-position switch, it has no

Select „Advanced" tab.

spring that would push back the device after releasing manual

pressure)

Parameter No. 1 - Activate / deactivate functions ALL ON / ALL

- Turning on/off the circuit - change the position of selected

OFF.

push-button from the current position.

Default value: 255

Options for changing parameter 255, 0, 1, 2

4. Controlling Fibaro Switch using a command: ALL

Available configuration parameters:

ON / ALL OFF

255 - ALL ON active, ALL OFF active.

0 - ALL ON is not active ALL OFF is not active

Fibaro Switch responds to commands ALL ON / ALL OFF that may

1 - ALL ON is not active ALL OFF active

be sent by the controller. ALL ON / ALL OFF commands are usually

2 - ALL ON active ALL OFF is not active

implemented in Z-Wave remote control.

Parameter No. 3 - Auto off relay after specified time, with the

By default, Fibaro Switch accepts both active commands ALL ON

possibility of manual override - immediate Off after button

and ALL OFF. Settings may be changed by entering an appropriate

push.

value into configuration register no. 1 (see configuration)

Default value: 0

Available settings:

0 - manual override disabled. After single button push the relay

turns on and automatically turns off after specified time.

5. Controlling Fibaro Switch using Home Center

1 - manual override enabled. After single button push the relay

controller

turns on and automatically turns off after specified time. Another

button push turns the relay off immediately.

After adding Fibaro Switch to the network, it will be represented in

Home Center by the following icon:

Parameter No. 4 - Auto off.

Default value: 0

Available settings:

[1- 65535] (0,1 s – 6553,5 s) Time period for auto off, in miliseconds

0 - Auto off disabled

Parameter No. 6 - Sending commands to control

assigned to 1-st association group (key no. 1).

Default value: 0

Available configuration parameters:

0 - commands are sent when device is turned on and off

Fig.3 Icon of Fibaro Switch shown by Home Center controller

1 - commands are sent when device is turned off. Enabling device

does not send control commands. Double-clicking key sends 'turn

on' command, dimmers memorize the last saved state (e.g. 50%

By default, FGS-212 device has a second hidden icon.

brightness).

It represents the second, virtual channel of the device triggered by

the second key. The user may add the association to this channel

2 - commands are sent when device is turned off. Enabling device

or trigger a scene.

does not send control commands. Double-clicking key sends 'turn

on' command and dimmers are set to 100% brightness.

Turning on/off the device connected to Fibaro Switch is performed

NOTE: Parameter 15 value must be set to 1 to work properly.

by pressing ON/OFF icon.

This activates the double-click functionality - dimmer/roller

shutter control.

IV Association

Parameter No. 13 - Assigns bistable key status to the device

status.

Association enables Fibaro Switch to directly control a device

Default value: 0

included in Z-Wave network e.g. Dimmer, Switch (ON-OFF), Roller

Shutter or scene (scene may be controlled only through the Home

Available configuration parameters:

Center controller).

0 - [On / Off] device changes status on key status change.

1 - Device status depends on key status: ON when the key is ON,

OFF when the key is OFF.

Association ensures direct transfer of control

commands between devices, and is performed

without participation of the main controller.

Fibaro Switch provides association of three groups.

1st group is assigned to key no. 1

Parameter No. 14 - Switch type connector, you may choose

between momentary and toggle switches.

2nd group is assigned to key no. 2

Default value: 1

3rd group reports state of devices. Only one device can be

Options for changing the parameter:

associated to this group.

0 - momentary switch

1 - toggle switch

Fibaro Switch enables user to control up to 5 normal devices, and

5 MultiChannel devices in group no. 1 and no. 2, group no. 3 has

only one field. One field is reserved for the network controller.

Parameter No. 15 - Operation of the Dimmer and Roller Shutter

Controller - enabling this option allows the user to dim

lighting/shut roller by associating Dimmer/Roller Shutter

To add an association (using the Home Center controller), go to

Controller and holding or double press of double switch (only

device options by clicking the following icon:

mono-stable switch).

Default value: 0

Select the "device options" tab. Then specify to which group and

what devices are to be associated. Sending relevant information to

Available configuration parameters:

0 - Dimmer/Roller Shutter Controller control is not active

devices added to associated groups may take even a few minutes.

1 - Dimmer/Roller Shutter Controller control is active

WARNING

When Fibaro Switch sends control commands and

Parameter No. 16 - Saving the state of the device after a power

a new command is issued, then the current one

failure. Fibaro Switch returns to the last position saved before

command transmission is interrupted to send new

a power failure.

commands.

Default value: 1

Options for changing the parameter 0-1

FGS-212 Fibaro Switch supports the operation of multi-channel

devices. Multichannel devices are devices that include two or more

0 - Fibaro Switch does not save the state after a power failure, it

circuits inside one physical unit.

returns to "off" position

1 - Fibaro Switch saves its state before power failure

devices

Remote control from Fibaro System is still

possible. This function is useful when you want

display status of external devices, e.g. Motion

Sensor, in Fibaro System.