Fibar Group FGS-212 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Przełącznik Fibar Group FGS-212. Fibar Group FGS-212 2 stron. Relay switch

Drukuj stronę

IX Guarantee

Possibility to change the configuration of the following

parameters [30 - 33].

1. FIBAR GROUP S.A. with its registered office in Poznan, ul.

Lotnicza 1, 60-421 Poznań, entered into the Register of

0 - DEACTIVATION - the device does not respond to alarm data

Entrepreneurs of the National Court Register maintained by the

frames

District Court for Poznań-Nowe Miasto and Wilda in Poznań, VIII

1 - ALARM RELAY ON - the device turns on after detecting an

Commercial Division of the National Court Register (KRS) under

alarm

number: 553265, NIP 7811858097, REGON: 301595664, share

2 - ALARM RELAY OFF - the device turns off after detecting an

capital PLN 1,182,100 paid in full, other contact information is

alarm

available at: www.fibaro.com (hereinafter "the Manufacturer")

3 - ALARM FLASHING - the device periodically changes its status

guarantees that the device sold (hereinaftr: "the Device" is free from

to the opposite, when it detects an alarm within 10 min.

material and manufacturing defects.

2. The Manufacturer shall be responsible for malfunctioning of the

Device resulting from physical defects inherent in the Device that

cause its operation to be incompatible with the specifications within

Parameter No. 30 - General Alarm, set for relay no. 1.

the period of:

- 24 months from the date of purchase by the consumer,

Default value: 3[byte] ALARM FLASHING

- 12 months from the date of purchase by a business customer (the

consumer and business customer are further collectively referred to

as "Customer").

3. The Manufacturer shall remove any defects revealed during the

Parameter No. 31 - Alarm of flooding with water, set for relay

guarantee period, free of charge, by repairing or replacing (at the

no. 1.

sole discretion of the Manufacturer) the defective components of the

Default value: 2[byte] ALARM RELAY OFF

Device with new or regenerated components. The manufacturer

reserves the right to replace the entire Device with a new or

regenerated device. The Manufacturer shall not refund money paid

for the device.

Parameter No. 32 - Smoke, CO, CO2 Alarm. Set for relay no. 1.

4. Under special circumstances, the Manufacturer may replace the

Device with a different device most similar in technical characteristics.

5. Only the holder of a valid guaranty document shall be entitled to

Default value: 3[byte] ALARM FLASHING

make claims under guarantee.

6. Before making a complaint, the Manufacturer recommends using

the telephone or online support available at https://www.fibaro.com/-

support/.

Parameter No. 33 - Temperature Alarm, set for relay no. 1.

7. In order to make a complaint, the Customer should contact the

Manufacturer via the email address given at https://www.fibaro.com/-

Default value: 1[byte] ALARM RELAY ON

support/.

8. After the complaint has been properly filed, the Customer will

receive contact details for the Authorized Guarantee Service

("AGS"). The customer should contact and deliver the Device to

Parameter No. 39 - Active flashing alarm time.

AGS. Upon receipt of the Device, the manufacturer shall inform the

Default value: 600

Customer of the return merchandise authorization number (RMA).

9. Defects shall be removed within 30 days from the date of

Available configuration parameters: [1-65535][ms]

delivering the Device to AGS. The guarantee period shall be

extended by the time in which the Device was kept by AGS.

10. The faulty device shall be provided by the Customer with

VI Additional Functionality

complete standard equipment and documents proving its purchase.

11. The cost of transporting the Device in the territory of the Republic

of Poland shall be covered by the Manufacturer. The costs of the

Operating alarm data frames

Device transport from other countries shall be covered by the

Customer. For unjustified complaints, AGS may charge the

Fibaro system allows user to set response of devices to alarm

Customer with costs related to the case.

situations

(response

data-frames ALARM_REPORT

and

12. AGS shall not accept a complaint claim when:

SENSOR_ALARM_REPORT) Fibaro switch responds to the

- the Device was misused or the manual was not observed,

following types of alarms:

- the Device was provided by the Customer incomplete, without

accessories or nameplate,

• General Purpose Alarm - GENERAL PURPOSE ALARM [0x00]

- it was determined that the fault was caused by other reasons than

• Smoke Alarm - ALARM CO2 [0x02], ALARM CO [0x01], ALARM

a material or manufacturing defect of the Device

SMOKE [0x03]

- the guarantee document is not valid or there is no proof of

• Water Flooding Alarm - ALARM WATER [0x05]

purchase,

• Temperature Alarm - ALARM HEAT [0x04]

13. The guarantee shall not cover:

- mechanical damages (cracks, fractures, cuts, abrasions, physical

Alarm data-frames are sent by devices that are system sensors (e.g.,

deformations caused by impact, falling or dropping the device or

flood sensors, smoke detectors, motion detectors, etc.).

other object, improper use or not observing the operating manual);

- damages resulting from external causes, e.g.: flood, storm, fire,

The device may respond in the following manner to received

lightning, natural disasters, earthquakes, war, civil disturbance, force

data-frames (settings are configured in configuration parameters,

majeure, unforeseen accidents, theft, water damage, liquid leakage,

see section V Configuration ):

battery spill, weather conditions, sunlight, sand, moisture, high or low

temperature, air pollution;

• 0 - DEACTIVATION - the device does not respond to alarm data

- damages caused by malfunctioning software, attack of a computer

frames

virus, or by failure to update the software as recommended by the

• 1 - ALARM ON - the device turns on after detecting an alarm

Manufacturer;

- damages resulting from: surges in the power and/or telecommuni-

• 2 - ALARM OFF - the device turns off after detecting an alarm

• 3 - ALARM FLASHING - the device periodically changes its status

cation network, improper connection to the grid in a manner

inconsistent with the operating manual, or from connecting other

to the opposite when it detects an alarm (lights on/off alternately)

devices not recommended by the Manufacturer.

- damages caused by operating or storing the device in extremely

adverse conditions, i.e. high humidity, dust, too low (freezing) or too

VII Operating Fibaro Switch

high ambient temperature. Detailed permissible conditions for

operating the Device are defined in the operating manual;

- damages caused by using accessories not recommended by the

Fibaro Switch may be operated using the following control elements:

Manufacturer

- damages caused by faulty electrical installation of the Customer,

− any controller compatible with the system (e.g. Home Center

including the use of incorrect fuses;

controller)

- damages caused by Customer's failure to provide maintenance and

− a mobile phone (e.g. iPhone and phones from other manufacturers

servicing activities defined in the operating manual;

with appropriate software)

- damages resulting from the use of spurious spare parts or

− tablet (such as iPad)

accessories improper for given model, repairing and introducing

− PC, using a web browser

alterations by unauthorized persons;

− push-buttons connected to inputs S1 and S2

- defects caused by operating faulty Device or accessories.

− service button B, located inside the housing (activates learn mode)

14. The guarantee shall not cover natural wear and tear of the

Device and its components listed in the operating manual and in

technical documentation as such elements have a defined

VIII Procedures for malfunctions

operational life.

15. The Device Guarantee shall not exclude, limit or suspend the

Customer's warranty rights.

The device does not respond to a pre-programmed transmitter:

16. The Manufacturer shall not be liable for damages to property

caused by defective device. The Guarantor shall not be liable for

• Make sure that the maximum range is not exceeded and the signal

indirect, incidental, special, consequential or punitive damages, or

path is not obstructed by metal surfaces such as metal cabinets, etc.

for any damages, including, inter alia, loss of profits, savings, data,

• Make sure the device is not in the programming mode,

loss of benefits, claims by third parties and any other damages

• Repeat the programming process.

arising from or related to the use of the Device.

Simplified EU declaration of conformity:

Hereby, Fibar Group S.A. declares that the device is in compliance

with Directive 2014/53/EU. The full text of the EU declaration of

conformity is available at the following internet address:

www.manuals.fibaro.com

WEEE Directive Compliance:

Device labelled with this symbol should not be disposed with other

household wastes. It shall be handed over to the applicable

collection point for the recycling of waste electrical and electronic

equipment.

Attention!

This product is not a toy. Keep away from children and animals!

This device complies with Part 15 of the FCC Rules

Operation is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including

interference that may cause undesired operation. This equipment

has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Notice

This device complies with Industry Canada license-exempt RSSs.

Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired

operation of the device.

Cet appareil est conforme aux normes d'exemption de licence RSS

d'Industry Canada. Son fonctionnement est soumis aux deux

conditions suivantes: (1) cet appareil ne doit pas causer d'interféren-

ce et (2) cet appareil doit accepter toute interférence, notamment les

interférences qui peuvent affecter son fonctionnement.

Note

Changes and modifications not expressly approved by the

manufacturer or registrant of this equipment can void your authority

to operate this equipment under Federal Communications

Commission's rules.

This Device may be used with all devices

certified with Z-Wave certificate and should be

compatible with such devices produced by

other manufacturers.

Any device compatible with Z-Wave may be added

to Fibaro system.