Sony Power HADFX HDC-P1 Instrukcja obsługi - Strona 9

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Aparat cyfrowy Sony Power HADFX HDC-P1. Sony Power HADFX HDC-P1 36 stron. Hd multi purpose camera
Również dla Sony Power HADFX HDC-P1: Broszura (36 strony), Broszura (4 strony), Broszura (4 strony), Broszura (2 strony)

Drukuj stronę

Sony Power HADFX HDC-P1 Instrukcja obsługi

e REMOTE connector (8-pin)

For connection to an RM-B150/B750 Remote Control Unit,

RCP-700/900-series Remote Control Panel, or MSU-900/950

Master Setup Unit.

f CAMERA POWER switch and indicator

To turn the power ON/OFF.

ON: Set the switch to the ? side.

OFF: Set the switch to the 1 side.

The indicator lights in green when the power is turned ON.

g DC IN (DC power supply input) connector (XLR 4-pin)

For connection to an AC-DN10 AC Adaptor, etc. to supply

power to the camera.

h "Memory Stick Duo" slot and access lamp

When you insert a "Memory Stick Duo" into the slot, the

access lamp lights in green.

The lamp is lit in red while writing/reading data to/from the

"Memory Stick Duo."

Caution

• Only a "Memory Stick" of Duo size can be used with the

camera.

• When the access lamp is lit in red, do not insert/remove the

"Memory Stick Duo" or turn off the camera.

i "Memory Stick" cap

Remove the cap before inserting a "Memory Stick Duo."

Caution

Do not use excessive force to pull the "Memory Stick" cap.

(LAN) connector (RJ-45 type, 8-pin)

To connect to a LAN. Use a LAN cable (shielded, category 5

or above) to connect to the hub of the LAN (10BASE-T/

100BASE-TX).

CAUTION

• For safety, do not connect the connector for peripheral

device wiring that might have excessive voltage to this port.

Follow the instructions for this port.

• When you connect the LAN cable of the unit to peripheral

device, use a shielded-type cable to prevent malfunction due

to radiation noise.

ATTENTION

Par mesure de sécurité, ne raccordez pas le connecteur pour

le câblage de périphériques pouvant avoir une tension

excessive à ce port. Suivez les instructions pour ce port.

VORSICHT

Aus Sicherheitsgründen nicht mit einem Peripheriegerät-

Anschluss verbinden, der zu starke Spannung für diese

Buchse haben könnte. Folgen Sie den Anweisungen für diese

Buchse.

k NETWORK indicator

To indicate the state when connected to a network system.

Lit: Successfully connected to an external control device

(MSU-900 series master setup unit, RCP-900 series

remote control panel, etc.).

Flashing: Unable to connect to an external control device

(MSU-900 series master setup unit, RCP-900 series

remote control panel, etc.) properly.

Off: A LAN cable is not connected or the connection settings

of the network system are not configured.

For details on the adjustment, see "Configuring Control

System Connection Settings" (page 12), "MAINTENANCE

Menu" (page 24), "DIAGNOSIS Menu" (page 28).

l GENLOCK (external sync signal input) connector

(BNC type)

To input an external sync signal (BB or 3-level sync) to

synchronize the camera.

Note

Even when a BB signal is used for the external sync signal, no

subcarrier phase-lock function is available for the VBS output

signal.

m SDI 1 (serial digital interface) connector and SDI 2

connector (BNC type)

For HD-SDI or SD-SDI signal output.

HD-SDI signal and SD-SDI signal output can be selected on

the menu. (It is not possible to select an HD-SDI signal and

SD-SDI signal separately for the SDI 1 connector and SDI 2

connector. One or the other needs to be selected.)

Note

The functions that can be displayed differ depending on the

output settings.

For details on the adjustment, see "Connector Output Settings

and Display Functions" (page 9).

n VBS connector (BNC type)

To output a VBS signal.

Caution

• The VBS output signal has no subcarrier phase-lock

function with respect to external sync signals.

• The functions that can be displayed differ depending on the

output settings.

For details on the adjustment, see "Connector Output Settings

and Display Functions" (page 9).

Connector Output Settings and Display

Functions

The functions that can be displayed differ depending on the

connector output settings.

Connector

Output

name

setting

Setting

Operation

Menus

status

SDI 1

HD/SD No

SDI 2

Yes

VBS

Yes

1) The focus assist functions include the VF DETAIL function and

FOCUS ASSIST INDICATOR function.

2) Linked to the DISPLAY/MENU switch setting.

3) A function can be set to ON/OFF on the OPERATION menu.

Display functions

Marker

Zebra

Focus

assist

Yes

Overview