Sony R-D-S EON MHC-2900 Instrukcja obsługi - Strona 15
Przeglądaj online lub pobierz pdf Instrukcja obsługi dla System stereo Sony R-D-S EON MHC-2900. Sony R-D-S EON MHC-2900 35 stron.
Drukuj stronęTo stop relay play
Press ll on the playing deck.
If you play both decks at the same time
You hear the sound from deck A.
When listening to a tape recorded with
the Dolby* noise reduction system
Press the DOLBY NR button to select B or
C. DOLBY NR B or C appears in the
display. The setting affects both decks.
Dolby noise reduction system reduces tape
hiss noise in low-level high-frequency
signals.
* Dolby noise reduction manufactured
under license from Dolby Laboratories
Licensing Corporation.
"DOLBY" and the double-D symbol O00
are trademarks of Dolby Laboratories
Licensing Corporation.
To reset the counter
Press the COUNTER A/B button to display
the counter for the deck you want to reset,
and then press RESET.
One Touch Play feature
Press [> or <J on the tape player when
the power is off.
When a tape is in the player, you will
immediately be able to listen to the tape
without pressing any other buttons. If no
tape is inserted, the system will just turn
on.
Ee
eee
Recording a CD
You can record from a CD to a tape. Use
TYPE I (normal), TYPE II (CrO,) or TYPE IV
(METAL) tapes.
You cannot listen to other sources while
recording.
Recording a CD
Automatically
By using the CD SYNCHRO button, you
can record from a CD to a tape quickly.
Use the buttons on the unit for this
operation. (See "Glossary".
POWER—ON
Before operation
1 Press [> to select the CD player.
If the player starts playing, press I to
stop play.
2 Press EFFECT on the amplifier so that
"EFFECT OFF" appears in the display.
11 Press & OPEN/CLOSE on the CD
player and place a CD. Then, press
& OPEN/CLOSE again to close the tray.
Total number of tracks and total playing
time appear in the display.
2 Press & and insert a blank tape into
deck B.
Make sure the tabs on the cassette have
not been removed.
3 select dual or single-sided recording
with DIRECTION and press DISPLAY.
To record
Press DIRECTION so that
One side
== appears
Both sides*
C=) or RELAY appears
*
Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
4 When you want to reduce the hiss noise
in low-level high-frequency signals,
press DOLBY NR to select B or C.
Dolby C provides greater noise
reduction benefit than Dolby B.
5 Press CD SYNCHRO.
"CD SYNC" appears in the display and
the deck B stands by for recording.
6 Press If PAUSE on the tape player to
release recording pause.
Recording starts.
To stop recording
Press lf on deck B or the CD player.
To change the display
Press DISPLAY so that CD player display
and Tape player display change alternately.
if the CD SYNCHRO button does not
operate
It means that you cannot record on this
cassette. (The tabs have been removed.)
Adjusting the volume will not affect
the recording level
But this control will change the sound
levels you hear through the speakers or
headphones.
Recording equalized or processed
sounds
If audio emphasis setting or a Personal File
is selected on the amplifier, the processed
sound can be recorded. When playing back
a recording that was made of a processed
sound, use EFFECT OFF mode. If the
processed sound is recorded and then the
playback is processed again, the resulting
sound may be distorted. To make a flat
(unprocessed) recording, use EFFECT OFF
mode.
What the [> and <1 indicators
indicate
The [> and << indicators light to indicate
which side starts recording.
They also tell you if a tab has been
removed.
if one indicator lights steadily and the
other indicator flashes for a few
seconds, then disappears
It means that recording will start from the
side which indicator lights steadily. If you
want to start recording from the other side,
press the other side button.
If one indicator lights steadily and the
other indicator neither lights nor
flashes
It means that you can record on only the
side which indicator lights steadily. (The
tab on the other side has been removed.)
if one indicator flashes steadily and the
other indicator neither lights nor
flashes
It: means that you can record on only the
side for which indicator flashes steadily.
Switch sides to start recording by pressing
the button of the side which is flashing.
If both indicators neither light nor
flash
It means that you cannot record on this
cassette. (Both tabs have been removed.)
continue to next page >
Chapter 4: the Tape Player