Cisco Linksys WAG200G Podręcznik użytkownika - Strona 9
Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Gateway Cisco Linksys WAG200G. Cisco Linksys WAG200G 39 stron. Linksys wireless-g adsl home gateway
Drukuj stronę
Chapter4
or data traffic; UBR (Unspecified Bit Rate) for applications
that are not time-sensitive, such as e-mail; or VBR (Variable
Bit Rate) for bursty traffic and bandwidth-sharing with
other applications.
NOTE:
If the QoS Type setting is CBR, then the SCR
Rate is not configurable. If the QoS Type setting
is UBR, then the PCR and SCR Rate settings are
not configurable.
PCR Rate
For the Peak Cell Rate (PCR), divide the DSL line
rate by 424 to get the maximum rate the sender can send
cells. Enter the rate in the field (if required by your service
provider).
SCR Rate
The Sustain Cell Rate (SCR) sets the average cell
rate that can be transmitted. The SCR value is normally
smaller than the PCR value. Enter the rate in the field (if
required by your service provider).
Autodetect
Select Enable to have the VPI/VCI settings
automatically detected, or select Dsable to enter the
values manually.
Vrtual Crcut
These fields consist of two items: VPI
(Virtual Path Identifier) and VCI (Virtual Channel Identifier).
Enter the settings provided by your ISP.
DSL
Modulaton
Select
MultMode, T1.13, G.dmt, G.lte, ADSL2, or ADSL2+.
Contact your ISP if you are not sure which mode to use.
Follow the instructions for your type of encapsulation.
RFC 2364 PPPoA
Some DSL-based ISPs use PPPoA (Point-to-Point Protocol
over ATM) to establish Internet connections. If you are
connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoA. If they do, you will have
to enable PPPoA.
Internet Connection Type > RFC 2364 PPPoA
Wreless-G ADSL Home Gateway
the
appropriate
mode:
Advanced Configuration
PPPoA Settings
Username and Password
Password provided by your ISP.
Connect on Demand: Max Idle Tme
the Gateway to cut the Internet connection after it has
been inactive for a specified period of time (Max Idle Time).
If your Internet connection has been terminated due to
inactivity, Connect on Demand enables the Gateway to
automatically re-establish your connection as soon as you
attempt to access the Internet again. To use this option,
select Connect on Demand. In the Max Idle Time field,
enter the number of minutes you want to have elapsed
before your Internet connection terminates. The default
Max Idle Time is minutes.
Keep Alve: Redal Perod
the Gateway will periodically check your Internet
connection. If you are disconnected, then the Gateway
will automatically re-establish your connection. To
use this option, select Keep Alve. In the Redial Period
field, specify how often you want the Gateway to check
the Internet connection. The default Redial Period is
30 seconds.
NOTE:
For
New
instructions:
1.
Select
RFC
23
Encapsulation drop-down menu.
2.
For the Virtual Circuit ID, enter 0 for the VPI
and 100 for the VCI.
Select VC for Multiplexing.
3.
4.
Select Multmode from the DSL Modulation
drop-down menu.
5.
Obtain the User Name and Password details
from your ISP.
RFC 2516 PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocol
over Ethernet) to establish Internet connections. If you are
connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoE. If they do, you will have
to enable PPPoE.
Enter the User Name and
You can configure
If you select this option,
Zealand,
follow
these
PPPoA
from
the
8