Pioneer DEH-1120MP Instrukcja instalacji - Strona 5

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Odbiornik samochodowy Pioneer DEH-1120MP. Pioneer DEH-1120MP 8 stron. Cd rds receiver

Drukuj stronę

Connections

4 Note:

19 Rear output

1 This product

Depending on the kind of vehicle, the function

(DEH-1120MP/DEH-1100MPB/

of 3* and 5* may be different. In this case, be

DEH-1100MP)

sure to connect 2* to 5* and 4* to 3*.

2 Antenna jack

3 Fuse (10 A)

6 Cap (1*)

5 Connect leads of the same

Do not remove cap if this

color to each other.

terminal is not in use.

7 Yellow (3*)

8 Yellow (2*)

Back-up

Connect to the constant 12 V supply

(or accessory)

terminal.

9 Red (5*)

10 Red (4*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

11 Black (chassis ground)

Connect to a clean, paint-free metal location.

12 ISO connector

13 Speaker leads

In some vehicles, the ISO connector may be

White: Front left

divided into two. In this case, be sure to

White/black: Front left

connect to both connectors.

Gray: Front right

Gray/black: Front right

Green: Rear left

Green/black: Rear left

Violet: Rear right

Violet/black: Rear right

Connections

20 This diaglam is for DEH-1120MP/DEH-1100MPB/DEH-1100MP .

23 Power amp

(sold separately)

21 To Rear output

22 Connect with RCA cables

14 Wired remote input

(sold separately)

Hard-wired remote control adaptor

can be connected (sold separately).

15 Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

16 Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

24 System remote control

17 Blue/white (7*)

Connect to auto-antenna relay control

terminal (max. 300 mA 12 V DC).

18 Blue/white (6*)

The pin position of the ISO connector will

25 Left

26 Right

differ depends on the type of vehicle.

Connect 6* and 7* when Pin 5 is an

27 Rear speaker

antenna control type. In another type of

vehicle, never connect 6* and 7*.

28 Perform these connections when using

the optional amplifier.

Connections

— Never band together multiple speaker's ne-

Important

gative cables.

! When this unit is installed in a vehicle without

! Control signal is output through blue/white

ACC (accessory) position on the ignition

cable when this unit is powered on. Connect it

switch, red cable must be wired to the term-

to an external power amp's system remote

inal that can detect the operation of the igni-

control or the vehicle's auto-antenna relay

tion key. Otherwise, battery drain may result.

control terminal (max. 300 mA 12 V DC). If the

vehicle is equipped with a glass antenna, con-

nect it to the antenna booster power supply

terminal.

! Never connect blue/white cable to external

power amp's power terminal. Also, never con-

ACC position

No ACC position

nect it to the power terminal of the auto anten-

! Use of this unit in conditions other than the

na. Otherwise, battery drain or malfunction

following could result in fire or malfunction.

may result.

— Vehicles with a 12-volt battery and negative

! Black cable is ground. This cable and other

grounding.

product's ground cable (especially, high-cur-

— Speakers with 50 W (output value) and 4

rent products such as power amp) must be

ohm to 8 ohm (impedance value).

wired separately. Otherwise, fire or malfunc-

! To prevent a short-circuit, overheating or mal-

tion may result if they are accidentally de-

function, be sure to follow the directions

tached.

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or ad-

Connection Diagram (Fig. 1)

hesive tape. To protect the wiring, wrap ad-

hesive tape around them where they lie

1 This product

against metal parts.

2 Antenna jack

— Place all cables away from moving parts,

3 Fuse (10 A)

such as gear shift and seat rails.

4 Note:

— Place all cables away from hot places,

Depending on the kind of vehicle, the function

such as near the heater outlet.

of 3* and 5* may be different. In this case, be

— Do not pass the yellow cable through a

sure to connect 2* to 5* and 4* to 3*.

hole into the engine compartment to con-

5 Connect leads of the same color to each

nect to a battery.

other.

— Cover any disconnected cable connectors

6 Cap (1*)

with insulating tape.

Do not remove cap if this terminal is not in

— Do not shorten any cables.

use.

Fig. 1

— Never cut the insulation of the power cable

7 Yellow (3*)

Abb. 1

of this unit in order to share the power

Back-up (or accessory)

Afb. 1

with other devices. Current capacity of the

8 Yellow (2*)

Рис. 1

cable is limited.

Connect to the constant 12 V supply terminal.

— Use a fuse of the rating prescribed.

9 Red (5*)

— Never wire the speaker negative cable di-

Accessory (or back-up)

rectly to ground.

Connections

10 Red (4*)

24 System remote control

Connect to terminal controlled by ignition

25 Left

switch (12 V DC).

26 Right

11 Black (chassis ground)

27 Rear speaker

Connect to a clean, paint-free metal location.

28 Perform these connections when using the

12 ISO connector

optional amplifier.

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to con-

nect to both connectors.

13 Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left +

Green/black: Rear left *

Violet: Rear right +

Violet/black: Rear right *

14 Wired remote input

Hard-wired remote control adaptor can be

connected (sold separately).

15 Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

16 Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

17 Blue/white (7*)

Connect to auto-antenna relay control term-

inal (max. 300 mA 12 V DC).

18 Blue/white (6*)

The pin position of the ISO connector will dif-

fer depends on the type of vehicle. Connect 6*

and 7* when Pin 5 is an antenna control type.

In another type of vehicle, never connect 6*

and 7*.

19 Rear output (DEH-1120MP/DEH-1100MPB/

DEH-1100MP)

20 This diagram is for DEH-1120MP/DEH-

1100MPB/DEH-1100MP .

21 To Rear output

22 Connect with RCA cables (sold separately)

23 Power amp (sold separately)