Pioneer CDJ-500II Instrukcja obsługi - Strona 15

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Odtwarzacz CD Pioneer CDJ-500II. Pioneer CDJ-500II 16 stron. Compact disc player
Również dla Pioneer CDJ-500II: Instrukcja serwisowa (6 strony)

Drukuj stronę

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this

component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components

and electrical appliances being used.

If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service

center or your dealer to carry out repair work.

Symptom

Door is not expelled when EJECT is

pressed.

When playback is started, it stops

immediately. Pauses or stops during

playback.

No sound

Sound is distorted, noise is output.

With certain discs, loud noise is

produced, or play stops.

When the auto cue function is set to

ON, track search is not finished.

Back cue function cannot be carried

out even though the CUE button is

pressed in playback mode.

Loop playback cannot be carried out

even though the LOOP OUT/EXIT

button is pressed.

The picture of the TV screen is

fluctuated or FM broadcast is

interfered with noise.

The disc is not rotating when the

power is ON.

Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal operation,

unplug the AC power cord and then plug it in again after the disc completely stops.

Should this product require service in the U.S.A. and you wish to

locate the nearest Pioneer Authorized Independent Service

Company, or if you wish to purchase replacement parts, operating

instructions, service manuals, or accessories, please call the

number shown below.

1- 800 - 872 - 4159

Please do not ship your product to Pioneer without first calling the

Customer Service Department at the above listed number for

assistance.

PIONEER ELECTRONICS SERVICE, INC.

CUSTOMER SUPPORT DIVISION

P.O. BOX 1760, LONG BEACH,

CA 90801-1760, U.S.A.

For warranty information please see the Limited Warranty sheet

included with your product.

Cause

÷ Power plug is disconnected from outlet.

÷ Disc is loaded upside down.

÷ Smudges on the disc, etc.

÷ Output cables are connected incorrectly or

loosely.

÷ Incorrect operation of audio mixer.

÷ Pin plugs and/or amplifier terminals are dirty.

÷ Player is in pause mode.

÷ Incorrect connections.

÷ Pin plugs and/or amplifier terminals are dirty.

÷ Interference is being picked up from a TV

set.

÷ Disc has a bad scratch or warp.

÷ Disc is extremely dirty.

÷ If the sound muted portion between

selections is long, searching time will be

long.

÷ If the sound muted portion is recorded for

about 20 seconds or more, playback will

start without the auto cue function.

÷ The cue point is not set yet.

÷ The cue point (loop in point) is not set yet.

÷ Interference is being picked up from the CD

player.

÷ The disc rotation stops automatically if no

operation has been performed for 80 minutes

or more in pause mode.

÷ Connect plug to wall outlet.

÷ Load the disc correctly with the label side UP.

÷ Clean the smudges from the disc and then play

it again.

÷ Connect properly.

÷ Check the settings of audio mixer switches and

sound volume controls.

÷ Clean away dirt.

÷ Press the PLAY/PAUSE button.

÷ Connect to audio mixer's LINE INPUT terminals.

Do not connect to MIC terminals.

÷ Clean away dirt.

÷ Switch OFF TV set, or move player away from

TV set.

÷ Replace the disc.

÷ Clean disc.

÷ Press TIME MODE/AUTO CUE button for more

than 1 second, and set the auto cue function to

OFF.

÷ Set the cue point. (See page 11.)

÷ Turn off POWER of the player, or move the

player away from TV or tuner.

÷ Playback can be started by pressing the PLAY/

PAUSE button. If the EJECT button is pressed,

the door will open.

Should this product require service in Canada, please contact a

Pioneer authorized dealer in Canada to locate the nearest Pioneer

Authorized Service Company.

Alternatively, please contact or ship your defective product freight

prepaid to one of the following Factory Service locations closest

to you:

Pioneer Electronics of Canada, Inc.

Factory Service East

300 Allstate Parkway

Markham, ON L3R 0P2

(905) 479-4411

For warranty information please see the Limited Warranty sheet

included with your product.

Remedy

Factory Service West

13911 Bridgeport Road

Richmond, BC V6V 1J6

(604) 278-1014