Whirlpool CGM2751KQ Instrukcja instalacji - Strona 3

Przeglądaj online lub pobierz pdf Instrukcja instalacji dla Suszarka Whirlpool CGM2751KQ. Whirlpool CGM2751KQ 27 stron. Commercial gas and electric dryer 120/240-volt, 60 hz

Drukuj stronę

1. Maintenance Instructions

The console

houses the accumulator

timer with actuating

arm and bufton,

The timer is set to provide

45 minutes

(4 pins) of drying time when activated

by the coin slide, Timer cams for

30- minute (6 pins) and 60-minute

(3 pins) drying times are included

the parts bag,

The coin-slide

mechanism,

control

panel

lock and key, and coin-box

lock

and key are not included

and are

available

from usual industry sources,

To change to a

30- or 60-minute

timingcam

Electrical Shock Hazard

Disconnect power before

making cam changes.

Failure to do so can result in

death or electrical shock,

Each coin-operated

dryer is

equipped

with a 45-minute

timer

cam that provides

45 minutes of

drying time when activated

by the

coin slide,

You can install the 30-minute

60-minute

timing cam (shipped

with

dryer) as follows:

1. Unlock meter case, Reach

into

control

panel

area,

2. Turn the timing cam by hand until

the "V" -shaped

notch

lines up

below the ratchet

tooth,

ratchet tooth

timing cam

drive

Line u

lug

clear

ratchet

hub

tooth,

down

3. Insert a narrow, flat-blade

screwdriver

under the timing cam

near the clock shaft, Gently lift cam

straight

up and off shaft making

sure that the "V" -shaped

notch

clears the ratchet

tooth,

4. Place new cam (hub side down)

over clock shaft, Line up flat side of

shaft with flat side of cam hole,

Check that drive lug is in place,

5. Turn cam until "V" -shaped

notch

lines up with ratchet

tooth,

6. Press cam down in place

on motor

shaft, Make sure that "V" -shaped

notch

clears the ratchet

tooth,

7. Close and lock the meter case,

Exhaust

requirements

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to do so can result in

death or fire.

Do not use non-metal

flexible vent,

metal vent that is smaller than four

inches in diameter

or exhaust

hoods with

magnetic

latches,

The dryer must be exhausted

outdoors.

Do not exhaust

dryer into a gas vent,

chimney,

wall, ceiling,

or concealed

space

of a building,

Do not install flexible vent in enclosed

walls, ceilings or floors,

If using an existing exhaust system, clean

lint from entire length of exhaust system,

Make sure exhaust hood is not plugged

with lint,

The exhaust system should be inspected

and cleaned

yearly,

Replace

any plastic or metal foil exhaust

vent with rigid metal or flexible

metal

vent,

Use 4" (10,2 cm) vent clamps to

secure vent system,

exhaust airflow

beffer

[==] good

_=]

Four-inch (1 0.2 cm) metal exhaust vent

isrequired, Plan installation to use the

fewest

number

of elbows and turns,

Metal flexible vent must be fully

extended

and supported

when the

dryer is in its final position,

DO NOT

KINK OR CRUSH THE VENT, The metal

flexible vent must be completely

open to allow adequate

exhaust air

to flow.

Allow as much

room as possible

when using elbows or making

turns,

Bend vent gradually

to avoid

kinking,

Remove excess flexible vent to avoid

sagging

and kinking that may result in

reduced

air flow,

Exhaust outlet is located

at the

center

of the boftom

dryer back,

The exhaust vent can be routed

up,

down,

left, right, behind

the dryer or

straight

out the back of the dryer,

Maximum

length of exhaust system

depends

upon the type of vent used,

number

of elbows and type of

exhaust

hood, The maximum

length

for both rigid and flexible vent is

shown in the chart,

EXHAUSTHOOD TYPE

(10.2cnQ

10.2cm)

of 900

Jums

0o=cm)

MAXIMUM

LENG1HRIGIDOF

METAL4"INCH_NT10"2

DIA_R

64 FT. (19.5 m)

64 FT. (19+5m]

58 FT.(17.7 m)

54 FT. (16.5 m)

54 FT. (16+5m]

48 FT.(14.6 m]

44 FT. (13_ m)

44 FT. (13_ m]

38 FT.(II.6 m]

35 FT. (10.7 m)

29 FT.(8.8 m)

27FT. ( 8.2m)

21FT. (6AnO

MA)0MUM LENGIH OF 4-INCH (10.2cm) DIAMElSR

FLI_IBLE MErAL VENT

36Fr.(11.0 m)

36FT. ( ll.Om)

28FT. ( 8_m)

31Fr. ( 9.4m)

31FT. ( 9Am)

23FT. ( 7.0 m)

27FT. ( 8.2m)

27FT. ( 8.2 m)

19FT. ( 5.8 m)

25 FT.(7.6 m]

25 FT.(7.6 m)

17 FT.(5.2 m)

23FT. ( 7.0m]

23FT. ( 7.0 m)

15FT. ( 4,6 m)

For exhaust systems not covered

the exhaust

length chart, see

Whirlpool

Service Manual,

"Exhausting

Whirlpool

Dryers," Part No, 603197,

available

from your Whirlpool

parts

distributor,

If dryer is installed in a confined area,

such as a bedroom,

bathroom or

closet, it must be exhausted

to the

outside and provision

made for

enough

air for combustion

and

ventilation,

(Check

governing

codes

and ordinances,)

See "Recessed

area

and closet installation

instructions"

Page 12,

Page 3