Zanussi ZEE6940 Podręcznik użytkownika - Strona 9

Przeglądaj online lub pobierz pdf Podręcznik użytkownika dla Hob Zanussi ZEE6940. Zanussi ZEE6940 16 stron. Product manaul
Również dla Zanussi ZEE6940: Podręcznik użytkownika (36 strony), Podręcznik użytkownika (48 strony), Podręcznik użytkownika (40 strony), Podręcznik użytkownika (12 strony)

Drukuj stronę

The minimum distance of 100 mm must be left

between the side edges of the cut out and ad-

jacent cabinets or walls.

The minimum distance (in line) between the

edges of the hob and flammable materials

above the hob is 400 mm. If the distance is

smaller, separate the flammable materials from

the edges of the hob by a minimum of 50 mm

Do not fit a cooker hood or combustible materi-

al lower than 650 mm above the hob.

For appliances installed in the Republic of Ire-

land please refer to NSAI- Domestic Gas In-

stallation I.S 813 Current Edition Section 7-

Permitted Locations of Appliance.

Installation

Warning! Read and follow the

instructions carefully. There is a risk of

injury or damage to the appliance.

• Make sure that there is no damage to the ap-

pliance from the transportation. Do not con-

nect a damaged appliance. Speak to the

supplier if necessary.

• Install built-in appliances only after you as-

semble the appliance into correct built-in

units and work surfaces. Make sure that

built-in units and surfaces obey the stand-

ards.

• Obey all orders and standards in force in the

country where you use the appliance (safety

standards, recycling standards, electrical

safety standards etc.)

Warning! Risk of injury from electrical

current.

• The electrical mains terminal is live.

• Make electrical mains terminal free of volt-

age.

• If the fixing bracket is near to the terminal

block, do not let the connection cable come

in contact with the edge of the bracket.

Electrical connection

• Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug (if

applicable).

www.zanussi.com

• The appliance must not be connected with

an extension cable, an adapter or a multiple

socket. There is a risk of fire.

• Do not let the power cable to heat up to a

temperature of more than 90° C. The cable

should be guided by means of clamps fixed

to the side of the cabinet, in order to avoid

any contact with the equipment beneath the

cooktop.

Electrical Requirements

Permanent electrical installation must agree

with the latest I.E.E. Regulations and local Elec-

tricity Board regulations. For your own safety

the installation must be done by a qualified

electrician (e.g. your local Electricity Board, or a

contractor who is on the roll of the National In-

spection Council for Electrical Installation Con-

tracting [NICEIC]).

The manufacturer refuses to be held re-

sponsible, if these safety measures are not

abided by.

Supply connections:

This hob has to be connected to 230 — 240 V

( 50 Hz) electricity supply.

The hob has a terminal block which is

marked as follows:

• L or 1 — Live terminal

• N or 4 — Neutral terminal

•

or E or 5 — Earth terminal

Before carrying out the connection, make sure:

1. The limiter valve and the electrical system

can take the appliance load (see the rating

plate)

2. The supply system is equipped with an effi-

cient earth connection in compliance with

the current standards and regulations

3. The outlet or omnipolar switch used for

connection is easily accessible with the

appliance installed.

You must purchase and install the power cable.

Use only a connection cable of type H05V2V2-

F T90 or its equivalent. Make sure that the ca-