Directed Xpresskit DBALL2 Podręcznik - Strona 14

Przeglądaj online lub pobierz pdf Podręcznik dla Przez blokady Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 19 stron. Ford5 remote start ready (rsr) installation
Również dla Directed Xpresskit DBALL2: Instrukcja instalacji (12 strony), Instrukcja instalacji (19 strony), Instrukcja instalacji (18 strony), Podręcznik (14 strony), Instrukcja instalacji (13 strony), Instrukcja instalacji (14 strony), Instrukcja instalacji (19 strony), Instrukcja instalacji (16 strony), Instrukcja instalacji (20 strony), Instrukcja instalacji (15 strony), Instalacja i skrócona instrukcja obsługi (16 strony), Instrukcja instalacji (18 strony), Instrukcja instalacji (16 strony), Instrukcja instalacji (18 strony), Instrukcja instalacji (16 strony)

Drukuj stronę

Platform: DBALL/DBALL2

Firmware: FORD5 Remote Start Ready (RSR) Installation

LED Diagnostics & Troubleshooting

LED

Description

Progra m m ing the Module

Module has no power.

Off

W aiting to begin the

Solid red

programming sequence.

CAN detected.

Flashes green

Bypass is waiting for Ignition

Solid orange

ON.

Bypass was skip.

Flashes orange

Ready for Key2GO

slowly

Module was successfully

Solid green

x 3 secs

programmed.

Module was successfully

Solid orange

x 3 secs

programmed without bypass.

Module Progra m m ing - Error Code s

Flashes red

CAN2 not detected.

x 2

Flashes red

Bypass data not detected.

x 3

Flashes red

Bypass processing error

x 4

Ex te rna l Module Synchronisa tion

Flashes red,

OBDII feature not supported.

red, then

orange x 10

Active Ground W hile Running

GROUND OUT ON (GW R)

Flashes green

command received.

IGNITION ON command

Flashes red

and orange

received.

Flashes green

START ON command received.

quickly

D2D a nd W 2W Com m a nds

Flashes orange

Lock command received.

x 1

Flashes orange

Unlock command received.

x 2

Trunk release command

Flashes orange

x 3

received.

RSR Code

3x OEM Lock Remote Start

Flashes

Activation was attempted when

red x7

RFTD feature is disabled.

Troubleshooting

Make sure the D2D harness is connected or that the 12 Volt is present

between the red and black wires. If the 12 Volt is present, the module

may be defective.

Make sure that all the connections are correct. See wiring diagram.

Normal operation.

Normal operation. Immobilizer bypass programming was skipped.

Normal operation. Follow the Key2GO programming.

Normal operation.

Normal operation. Immobilizer bypass programming was skipped.

Check the Tan - Tan/Black wire connections. W ake up the data bus by

turning the ignition on and try again.

Check the bypass line connection. If more than one wire is used, make

sure they are not inverted. Start vehicle using the key to confirm the

OEM equipment is still operational.

Bypass calculation failed. Reset the module and try again. Might be

caused by a bad reading in the first programming attempt or by an

unknown bypass value. If a second attempt fails, connect the module

to Directechs and call Tech Support with the module ID in hand.

Diagnostic data bus not detected. Some features are not supported by

SmartStart. This can be caused by missing wire connections or

module hardware limitation. Refer to "Installation (wiring diagrams &

vehicle wiring reference charts)" to check the connections.

Otherwise, the Ground W hile Running (status) signal was lost or was

never received by the module.

Otherwise, the ignition signal was not received by the module.

Otherwise, the start signal was not received by the module.

If the bypass module fails to flash, it means the module did not receive

the signal. Verify the connections between the bypass and the remote

starter module.

Activated from W eb automatically when using RSR flash tool or can be

done manually.

Rev.: 20160317

Page 14