Alemite 9911-R1 Instrukcja serwisowa - Strona 10
Przeglądaj online lub pobierz pdf Instrukcja serwisowa dla Pompa wodna Alemite 9911-R1. Alemite 9911-R1 12 stron. High-pressure stripped pump
Również dla Alemite 9911-R1: Instrukcja serwisowa dla właścicieli (16 strony), Instrukcja serwisowa (12 strony)
Drukuj stronę
SER 9930
IMPORTANT: If a primer is used with Loc-
tite 222, the curing time is greatly reduced.
13. Screw the Lower Tube [with Loctite 222] into the
Upper Tube.
• Follow the thread sealant manufacturer's
recommendations.
• Do not tighten at this time.
14. Install the Rod assembly into the Upper Tube until it
protrudes from the Lower Tube.
• Use care not to damage the Seal.
15. Install Seal (35) [heel end first] into Foot Valve (36).
16. Install Stop (34), the Foot Valve assembly [Seal end
first], Gasket (32), Seat (37) [small diameter end
first], and additional Gasket (32) over the Primer Rod
and into the Lower Tube.
17. Install Primer Disk (39) onto the Primer Rod.
• Make sure the hole align.
18. Install Roll Pin (40) that secures the Primer Disk to
the Primer Rod.
19. Screw Primer Body (41) [with Loctite 222] into the
Lower Tube.
• Follow the thread sealant manufacturer's
recommendations.
• Do not tighten at this time.
CAUTION
Install the Rod and Tube assembly into the Body
with a twisting motion. Use care not to damage
the Seals.
20. Install the Rod and Tube assembly into the Body and
at the same time screw the Upper Tube [with Loctite
222] into the Body.
• Follow the thread sealant manufacturer's
recommendations.
21. Tighten all the threaded pump tube components into
one another.
• Place a bar or other suitable tool in the holes of the
Primer Body for leverage.
• Tighten sufficiently to properly crush all Gaskets.
22. Install O-Ring (8) onto the upper groove of Body (10).
Step for Model 9979-M Only
23. Screw Adapter (21) [with Loctite 242] into the Body
as required.
Revision (8-10)
Air Piston
CAUTION
Use care not to switch Washers (3 and 7). Compo-
nent damage can occur.
24. Install Washer (7) [brass color] and O-Ring (6) onto the
Rod.
25. Install Quad-Ring (5) onto Air Piston (4).
26. Place the Air Piston (observe THIS SIDE UP) on top of
the Rod.
27. Install Washer (3) [silver color] and Nut (2) that
secures the Air Piston to the Rod.
• Tighten the Nut securely.
NOTE: Place an appropriate size punch or
other suitable tool into the hole of the Rod.
See Figure 2-A.
Model 9930 Only
28. Install and seat O-Ring (17) into the groove of Camlock
Adapter (18).
29. Install the Camlock Adapter onto the pump tube.
• Make sure the Screw holes align.
30. Install Lock Washers (19) and Screws (20) that secure
the Camlock Adapter to the Body.
• Tighten the Screws securely.
Attach Air Motor to Pump Tube
1. Clamp the pump at the flats of Body (10) securely in a
soft-jaw vise.
2. Install the Bottom Cap onto the Body.
3. Install O-Ring (8) onto the upper groove of the Body.
CAUTION
Install the Cylinder with care. Damage to Quad-
Ring (5) and/or O-Ring (8) can occur.
HINT: Angle the Cylinder onto the Quad-
Ring.
4. Install the Cylinder over the Body's O-Ring and seat it
properly onto the Bottom Cap.
10
High-Pressure Grease Pump
Alemite, LLC