Nikon FSB-5 Instrukcja obsługi - Strona 2

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Akcesoria do kamer Nikon FSB-5. Nikon FSB-5 2 stron. Fieldscope digital camera bracket

Drukuj stronę

Thank you for purchasing Nikon's Fieldscope Digital Camera Bracket for the COOLPIX

S series. Using your digital camera in combination with a Fieldscope enables you to

take super-telephoto digital pictures. Furthermore, when used in combination with a

Nikon EZ-Micro Fieldmicroscope this bracket enables photomicroscopy.

Items supplied

• Bracket x 1

• Cable release (50cm) x 1

• Bracket ring FSBR-5 x 1 (comes attached to the bracket)

Note: Bracket ring FSBR-5 cannot be used with other brackets.

1 Cable release socket

2 Bracket fixing screw

3 Eyepiece lens socket

4 Bracket ring (FSBE-5)

5 Body

6 Light interception hood

Attaching the FSB-5 to a digital camera

1. Setting up the digital camera

• Preparations for use (Fig. A)

1) Adjust the positioning block (7) to fit your particular COOLPIX digital camera.

a) Pull up the positioning block (7) to allow it to be rotated. (Fig. a)

b) Referring to the "Number and COOLPIX digital camera" information shown

immediately below, rotate the positioning block to adjust the number. (In Fig. b, it

is set to "1".)

c) Push back the positioning block (7) to complete the setting.

Number and COOLPIX digital camera

1: S6, S7, S7c

2: S9

2) Push the shutter button (8), as shown in Fig. d.

• Setting up

1) Slide the COOLPIX to the left, then lightly fasten the camera mount screw (!w) to secure

the position. The camera mount (!p) should remain movable. (Fig. B)

2) Adjust the position of the camera mount (!p), then, while keeping the COOLPIX pressed

against the positioning block (7), fit the projection on the mount into the base of the

COOLPIX. (Fig. C)

3) While keeping the COOLPIX pressed against the positioning block (7), tighten the

camera fixing screw (!w). (Fig. D)

4) Press the COOLPIX against the positioning plate (9) and tighten the camera mount screw

(!q) to secure the COOLPIX in place. (Fig. E)

2. Removing the digital camera (Fig. F)

1) Release the camera mount screw (!q).

2) Next, release the camera fixing screw (!w) until it leans as shown in the photo.

3) While taking care to avoid touching the shutter button (8), remove the COOLPIX from

the camera mount (!p).

3. Removing bracket ring FSB-5

1) Remove the FSB-5 by inserting a finger in the ring from the side of eyepiece lens socket

(3) and pulling.

2) The FSB-5 can be removed by pushing the area marked ★ in Fig. F.

Notes:

• Do not tighten the camera mount screw (11) or the camera fixing screw (12) excessively.

• Even when the shutter button is not placed over the center of the COOLPIX shutter release

button of, you can shoot. If you are unable to do so, realign your COOLPIX with the FSB-5.

1 Screw the eyepiece (A or B) into the eyepiece

socket.

2 Attach the assembly in C to the eyepiece or the EZ-

Micro Fieldmicroscope.

* While fixing it in place, keep the bracket pressed.

With the 16x/24x/30x Wide DS Eyepiece, attach the

bracket ring FSBR-5 to the bracket FSB-5.

• Press the bracket ring against the bracket until the

black rubber ring snaps into the groove on the

bracket.

• If the bracket ring is not attached or not attached

securely, shade may appear in the four corners of the

image.

With other eyepieces, remove the bracket ring FSBR-5.

• The bracket ring can be removed by inserting a

finger in the ring and pulling. (It may be tight due to

resistance from the rubber.)

• If the bracket ring is not removed, the four corners of

the image will appear more shaded.

A Wide MC or MC II Zoom Eyepiece with FSA-1

and FSA-2 attached.

B Fieldscope Eyepiece (16x/24x/30x, 27x/40x/50x,

40x/60x/75x) Wide DS.

C COOLPIX S series (except S2, S4, S10) with

Digital Camera Bracket FSB-5 attached.

[Focal length (35mm [135] format equivalent) with FSB-5] = [Focal length (35mm [135] format equivalent) of the COOLPIX S series (except S2, S4, S10)] x [magnification of eyepiece]

Nomenclature

7 Positioning block

8 Shutter button

9 Positioning plate

!p Camera mount

!q Camera mount screw

!w Camera fixing screw

3: S5, S8

4: S1, S3

Fieldscope

Use the following COOLPIX settings. Keep other settings at their original default positions.

• With [MENU]

Image mode

Continuous

AF area mode

Sensitivity (ISO)

• With [SET UP]

AUTO OFF

AF assist

Blur warning

• Focusing

Focus first using controls on the Fieldscope or EZ-Micro, then make fine adjustments with the

camera's AF function.

• Shooting

Use the cable release, depressing it gently.

• Camera zoom setting

When shooting with the zoom at a wide-angle setting, depending on the type of eyepiece you

are using, the four corners of the image may appear shaded, giving it a rounded appearance.

With the MC or MC II Zoom Eyepiece, we recommend using the maximum telephoto setting.

• When the AF lamp does not turn on

After locking the focus by pressing the shutter release button halfway, set the focus by

adjusting the focus ring on the Fieldscope or the focus knob on the EZ-Micro while viewing the

LCD monitor. This turns on the AF lamp.

Notes for shooting

• Use a solid tripod during super-telephoto or super-closeup shooting to ensure steady images.

• Beware of camera shake as small vibrations at high magnification can ruin a photograph.

• With super-telephoto or super-closeup shooting, it may be difficult to obtain a precise focus

with the camera's AF function. We recommend that you take a series of pictures of the same

subject in sequence, to ensure that you capture the desired image.

If vignetting occurs

• If vignetting occurs at the right edges of your images or in the camera's LCD monitor, the

camera may not have been correctly attached to the equipment. Re-attach the camera and

confirm proper camera alignment while viewing the LCD monitor.

• In wideangle, vignetting may occur with any COOLPIX digital camera.

Note for carrying

• For carrying or transport, we recommend that you remove the bracket from the lens or EZ-

Micro Fieldmicroscope.

Fig. a

Fig. b

Fig. A

Fig. C

Fig. E

Attachment

Wide MC or MC II Zoom Eyepiece +

FSA-1&-2

Fieldscope Eyepiece

16x / 24x / 30x Wide DS

27x / 40x / 50x Wide DS

EZ-Micro

40x / 60x / 75x Wide DS

Camera settings

FINE

Continuous

Manual (Not available on some COOLPIX models.)

5 minutes

OFF

OFF (Not available on some COOLPIX models.)

Setting for shooting

(Fig. c) When

the button is

not pushed.

(Fig. d) When

the button is

pushed.

COOLPIX S series (except S2, S4, S10)

Digital Camera Bracket FSB-5

Bracket ring FSBR-5 for

16x/24x/30x Wide DS

Eyepiece

Fig. B

Fig. D

Fig. F