CustomWorks NITRO ROCKET KIT 0715 Podręcznik - Strona 8

Przeglądaj online lub pobierz pdf Podręcznik dla Zmotoryzowany samochód zabawka CustomWorks NITRO ROCKET KIT 0715. CustomWorks NITRO ROCKET KIT 0715 16 stron.

Drukuj stronę

Shock Bag

Bag J

-Parts for

Step#1

1424

Qty 4

Long Shock Body

-Parts for

Step#2

1432

Qty4

Eyelet Cap

-Parts for

Step#3

1433

Qty4

Spring Collar

STEP #1

NOTE: Put a few

drops of oil on the

O-Rings!

1424

1434

TIP: To press clip in easiest, compress the

clip so the diameter is a little smaller.Insert

1250

open end of clip first, working counter-

1435

clockwise to the bent end as shown.

SHOCK FILLING INSTRUCTIONS:

1) Holding the

2) Slowly move the

shaft up and down

shock upright,

fill with oil until

several times to allow

the top of the

air bubbles to escape

body.

to the top.

SUGGESTED

40 WT R/C

SHOCK OIL.

6) Then the shaft

7) If the shock does not push

should push itself

out this far there is not enough

out to its full length

oil in it. Add just a little oil and

slowly.

try steps 5-6 again.

8) If the shockrebounds too fast , or you cannot

push the shaft in until the eyelet hits the body, there

is too much oil. Loosen the cap and pump out a

small amount of oil by pushing the shaft in. Re-

tighten the cap and try steps 5-6 again.

Shock Assembly

1428

Long Shock Shaft

1431

Qty4

Threaded Cap

REAR

FRONT

1804

Qty2

1807

Qty2

(WHITE) Spring

(GREEN) Spring

5230

1436

1428

- Attach 1436 Shock Piston to

1428 Shaft using 5230 E-Clips

to secure.

- Press 1250 O-rings into 1424

Shock Body followed by 1434

Shaft Guide. Retain using 1435

Clip.

Filling Shocks: Steps 1-4

3) Refill with

oil to the top

of the shock

body.

Qty4

1434

Qty4

Shaft Guide

1437

Qty 4

FIRM Bladder (BLACK)

1407

Qty4

1408

Spring Bucket

Mount Ball

STEP #2

- Snap Pivot Ball into the 5228 Ball End. Thread

the Ball End onto the Shock Shaft until the Ball

End is flush with the end of threads on the shaft.

- Press 1432 Eyelet Cap into 1431 Threaded

Shock Cap so that guide in the Eyelet Cap lines

up in the recess in the Threaded Shock Cap.

- Press the 1437 Firm Bladder (BLACK) into the

Threaded Shock Cap so the dome of the

bladder points away from the Eyelet Cap.

- Fill the Shock Body with oil to the top then

thread the Eyelet Cap assembly onto the

Shock Body until tight.

-NOTE: See shock filling tips for more

instructions.

4) Thread the Eyelet Cap

assembly onto the Shock

Body until it is hand

tight. Oil should seep

out of the bleed hole

in the Threaded Cap.

STEP #3

- Thread 1433 Spring Collar onto

the shock. Slide the springs onto

the shock and secure using the

1407 spring bucket as shown.

- Press 5278 Screws thru the holes

on the front tower and thru the

upper/middle set of holes on the

rear tower. Secure using 5217

Nut.

- Install the shocks onto the screws

with the shoulder of the 1408

Mount Ball facing the tower, secure

with 5217 Nut.

- Attach the shock to the susp arms

in the outer most holes on both

front and rear arms as shown.

1250

Qty 8

1435

Qty 6

O- Ring

Reatining Clip

1:1

5228

Qty4

Short Ball End

5278

Qty 4

Qty4

4-40 x 1" SH Screw

Setting Shock Rebound: Steps 5-8

5) Move the shock shaft in and out a

few times and then push it all the way

in. It should be easy to push the shaft

in until the eyelet hits the body.

5278

5217

ATTACH HERE

5278

UPPER/

MIDDLE

HOLE

1:1

1436

Qty4

5230 Qty 10

Piston

E-Clip

5228

Qty4

Pivot Ball

5274

Qty 4

5217

Qty 8

4-40 x 1/2 SH Screw

4-40 Lock Nut

1431

1432

1437

5228

1408

1477

1433

GREEN SPRINGS FRONT

WHITE SPRING REAR

1407

5217

1433

ATTACH HERE