CustomWorks NITRO ROCKET KIT 0715 Podręcznik - Strona 9

Przeglądaj online lub pobierz pdf Podręcznik dla Zmotoryzowany samochód zabawka CustomWorks NITRO ROCKET KIT 0715. CustomWorks NITRO ROCKET KIT 0715 16 stron.

Drukuj stronę

Bag J

Bag K

Fuel Tank / Motor Mounts

Bag K

Fuel Tank / Motor Mounts

-Parts for

Step#1

4350

Qty 1

Fuel Tank

STEP #1

- Attach the 4450 Fuel Tank to the chassis using the

5264 Screws.

- Mount the 3270 Motor Mounts using the 5290 Motor

Mount Screws. The slanted edge of the mount will face

toward the spur gear.

- Mount the 3262 Pipe Mount using the 5264 Screws

and 5205 Nuts.

-Thread the 4966 Set Screw into the pipe mount, this

will be used to secure the wire coming from your

exhaust pipe to the car.

NOTE: The extra 5290 screws are to mount your nitro

motor after completion of the Clutch Bag.

Bag K

Servo and Linkage Installation

-Parts for

Steps

#1&#2

5242

Qty 1

Large Servo Saver

-Parts for

Step#3

5246

Qty1

Carb Ball Cup

-Parts for

Step#4

5215

Qty1

2-56 Ball End

STEP #1

- Attach 5240 Servo Mounts to your steering servo in the

position shown using 5253 Screws. ALSO do this for throttle

servo in the same position as well now.

- Thread 8122 Ball Stud into the upper-most center hole in the

5242 Servo Saver using the 3234 Spacer.

- Attach both 8130 Ball Cups to one another using the 5281

Stud until the Ball Cups bottom out on one another. Snap a

Ball Cup onto the Ball Stud on the Servo Saver.

- Determine which of the Spline Inserts are correct for your

servo by pressing it over the drive on the servo. Align the

servo so it has equal throw in both directions.

- Press the Servo Saver onto the Spline Insert so that the Servo

Saver is perpendicular to the servo, attach using the screw

that came with your servo.

- 3234 SPACER IN STEPS 1&2 USED TO LEVEL

THE DRAG LINK WITH DIFFERENT SERVOS.

5240

3270

Qty 2

3262

Qty 1

Motor Mount

Pipe Mount

5240

Qty4

8130

Qty2

Servo Mount

Small Ball Cup

5246

Qty2

5246

Qty5

Spring

Collar

5215

Qty1

5232

Qty1

2-56 Pivot Ball

2-56 Cone Spacer

3234

5253

8130

4966

Qty 1

5264

4-40 Set Screw

4-40 x 1/2 FH Screw

4350

5217

4966

5264

5281

Qty1

8122

Qty 2

3234

4-40 Stud

Ball Stud

Spacer

1:1

5282

Qty 5

5246

Qty1

4-40 Set Screw

Swivel

1:1

5246

Qty2

5252

Qty 1

Fuel Tubing

4-40 x 1/4 BH Screw

STEP #2

- Mount the servos to the chassis using 5263 Screws as

shown.

- Thread the 8122 Ball Stud into the top of the Steering

Slide, Snap the Ball Cup onto the Ball Stud.

-Using double sided tape, mount your reciever to the

top of the steering servo.

- Attach 3209 Antenna Mount in either of the two

holes shown below.

NOTE: Steering movement should be bind free except

for the restriction of the servo transmission.

8122

8130

5281

5242

1:1

Qty 2

5263

Qty 3

5290

4-40 x 3/8 FH Screw

M3 x 8MM SH Screw

5263

Qty 2

5253

3209

Qty1

4-40 x 3/8 BH Screw

Antenna Mount

5246

Qty1

5246

Qty1

Steel Snap

Servo Horn

1:1

5201

Qty 1

5204

Qty 1

2-56 x 1/2 SH Screw

2-56 Lock Nut

3209

8122

*3234 SPACER

UNDERNEATH*

5263

1:1

Qty 8

5217

Qty 2

4-40 Lock Nut

3270

5290

1:1

Qty 8

5263

Qty 9

4-40 x 3/8 FH Screw

5228

Qty1

Throttle Rod (SHORT)

5228

Qty1

Brake Rod (LONG)

- 3234 SPACER IN STEPS 1&2 USED

TO LEVEL THE DRAG LINK WITH

DIFFERENT SERVOS.