Asko D3232 Instrukcja obsługi i konserwacji - Strona 8
Przeglądaj online lub pobierz pdf Instrukcja obsługi i konserwacji dla Zmywarka Asko D3232. Asko D3232 16 stron. User manual d3232 use & care guide fr (french ucg 2+1 warranty)
Również dla Asko D3232: Skrócona instrukcja obsługi (2 strony), (Hiszpański) Uso Y Cuidado (16 strony), (Angielski) Instrukcja obsługi (16 strony)
Drukuj stronę
PO
PO
WER BUTT
WER BUTT
POWER BUTT
PO
PO
WER BUTTON
WER BUTT
Use this button to turn the main power to the unit on
and off. The location of the power button is illustrated
on page 8.
STAR
ST
ST
AR
AR
ART/ST
T/ST
T/ST
T/STOP BUTT
OP BUTTON
OP BUTT
OP BUTT
ST
ST
AR
T/ST
OP BUTT
Once you have selected the wash program and
temperature and drying options, press this button then
close the door to start the dishwasher. (Make sure the
door is securely closed.)
INTERRUPTING A PROGRAM
INTERRUPTING A PROGRAM
INTERRUPTING A PROGRAM
INTERRUPTING A PROGRAM
INTERRUPTING A PROGRAM
T T T T T O O O O O ADD
ADD
ADD
AN ITEM
AN ITEM
ADD
ADD AN ITEM
AN ITEM
AN ITEM
If you want to interrupt a program to add an item, open
the door slightly until the spray arms stop turning. You
can then open the door fully and place the item into the
dishwasher. Close the door securely. The program will
continue from where it was interrupted.
WARNING!
Be extremely careful when opening the door during
a program. The water is hot and you could get
scalded.
CHANGING OR ST
CHANGING OR ST
CHANGING OR STOPPING
CHANGING OR ST
CHANGING OR ST
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
If you decide to change the program after you have started
the machine, press the Start/Stop button for three
seconds. You will have to select the program and
options again when you are ready to restart the program.
(Note: If the program has already gone through the wash
cycle, you will have to add detergent.)
PROGRAM TIMES
PROGRAM TIMES
PROGRAM TIMES
PROGRAM TIMES
PROGRAM TIMES
The program times may not always be the same
because of variations in the household hot water
temperature. The dishwasher heats the water to the
proper temperature for the program selected; so if the
temperature of the water entering the dishwasher is
too low, the dishwasher will run longer because it takes
longer to heat the water. Raising your water heater
setting could help to shorten the cycle times.
F F F F F A A A A A UL
UL
ULT MESSA
UL
T MESSAGES
T MESSA
T MESSA
UL
T MESSA
In the event that the machine should fail during a
program, the control panel lights will flash to indicate an
operation fault has occurred. The table below defines
these signals and gives possible causes and solutions.
See also "Troubleshooting" on page 12.
Flashing Indicator Light(s)
Heavy Wash
Delicate Wash
Quick Wash
Pots and Pans and Heavy Wash
Pots and Pans and Normal Wash
Page 8
ON
ON
ON
ON
ON
ON
ON
ON
OPPING
OPPING
OPPING A A A A A
OPPING
GES
GES
GES
GES
Type of Fault and Recommended Action
Too much water has entered the dishwasher. Call a service technician.
Water inlet fault. Make sure the water supply is open.
Valve leakage. Shut off the water supply and contact a service technician.
The drain is blocked. See "Troubleshooting" on page 12.
The filter is clogged. See "Cleaning the Filters" on page 9.
CHILD-SAFE
CHILD-SAFE
CHILD-SAFE
CHILD-SAFE
CHILD-SAFE
FEA
FEATURE
FEA
TURE
TURE
TURE
FEA
FEA
TURE
As a safety measure, Model D3232 can be programmed
not to start unless the Temperature and Drying buttons
are held down simultaneously. To program this feature,
follow the steps below:
1. Turn off the power to the machine.
2. Simultaneously press and hold down the
Temperature and Drying buttons as you turn on the
power to the machine. The Temperature, Drying and
Start buttons will flash.
3. Release the buttons.
4. Press the Program button. The Pots and Pans
button will glow to indicate the button lock is activated.
5. Press Start to confirm your selection and return to
main menu.
Once the child-safe feature is active, the Temperature
and Dry buttons will flash whenever you press any of
the buttons. To deactivate the button lock, press the
Temperature and Dry buttons simultaneously . You can
then select the program and options and press Start to
start the unit. The lock will reactivate automatically in
three minutes.
To permanently deactivate the button lock, repeat the
steps above. The Pots and Pans button will go out to
indicate the button lock is off.
END-OF-PROGRAM SIGNAL
END-OF-PROGRAM SIGNAL
END-OF-PROGRAM SIGNAL
END-OF-PROGRAM SIGNAL
END-OF-PROGRAM SIGNAL
Model D3232 can be programmed to emit a short signal
when the program is finished. To program this feature,
follow the steps below:
1. Turn off the power to the machine.
2. Press and hold down the Delay Start button as you
turn on the power to the machine. The Delay Start
button will flash.
3. Release the button.
4. Press the Program button. The Pots and Pans
button will glow to indicate the end-of-program
signal is activated.
5. Press Start to confirm your selection and return to
main menu.
To deactivate the signal, repeat these steps. The Pots
and Pans button will go out to indicate the signal is off.
If you have corrected the fault, turn the main power off
then back on to remove the fault indication. If it still
displays, try again to correct the problem or call a service
technician.
BUTT
B
B
UTTON
UTT
UTT
ON
ON
ON
B
B
UTT
ON