Coinco Vantage Series Manual de instalação e operação - Página 2

Procurar online ou descarregar pdf Manual de instalação e operação para Terminal de pagamento Coinco Vantage Series. Coinco Vantage Series 4 páginas.

Imprimir página
Unpacking the Bill Acceptor
After removing the bill acceptor from the shipping
carton, inspect it for possible damage. If the unit is
damaged, notify the shipping company immediately.
The consignee (person or company receiving the unit)
can fi le a claim against the carrier for shipping
damage. We recommend you keep the original
carton and packaging materials to reuse if you need
to transport or ship the bill acceptor in the future.
If the bill acceptor is being stored or used as a spare,
always keep it in its shipping carton when not in use.
This will keep it clean and offer the best protection for
the unit
Option Switch Settings
See Figure 2. This step is not necessary for MDB
applications.
Option / Dip Switch Settin
Note: There are no switches on MDB only models.
Note: There are no switches on MDB only models.
Pulse Timing
50 / 50mS
150 / 150mS
Custom
(default is 200/200mS)
(Credit Line) VL Models Only
Parallel
Switch 3
Switch 3
Switch 4
Switch 4
Switch 5
Switch 5
Switches 6 - 8
Switches 6 - 8
NOTE: Power MUST be reset for
revised switch settings to take effect.
gs
ON
ON
ON
ON
OFF
OFF
OFF
OFF
Switch 1
Switch 1
Switch 2
Switch 2
ON
ON
ON
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
4 P u lse/$ 1 P u lse/$
4 P u lse/$ 1 P u lse/$
A lw a ys
A lw a ys
H o st
H o st
E n a b le d
E n a b le d
E n a b le d
E n a b le d
S e rial
S e rial
P u lse
P u lse
Reserved
Reserved
Figure 2
2
Installing the Bill Acceptor
1.
Remove power from the host machine.
DO NOT connect the bill acceptor harness to
the machine with power connected.
2. Install the bill acceptor into the host machine
using the mounting studs and hardware in the
machine. To simplify installation, see Figure 3.
3. Install / connect the proper interface harness
to the host machine.
4. Restore power to the machine.
5. The illuminated bill inlet will begin to fl ash and
the stacker motor will cycle upon power-up. If
this does not occur, check the wiring harness
connections and make sure power is applied.
6. Check the Vantage diagnostic LED on the back
of the unit Figure 1 to verify it is green and ON
continuously. If it is not, you can troubleshoot
based on the status shown on the billbox decal or
Figure 8.
7. With the vend price set below one dollar, insert
a one dollar bill.
8. Verify credit has been established.
9. Check the bill box to see that the one dollar bill
was properly stacked.
Quick Release
Bezel Operation
1.
1.
P u s h f i r m l y o n Q u i c k R e l e a s e T a b s u s i n g
a s c r e w d r i v e r t i p . T a b s w i l l m o v e t o w a r d s
b e z e l a n d l a t c h .
2.
2.
O n c e b o t h t a b s a r e l a t c h e d , t h e b i l l
a c c e p t o r w i l l s e p a r a t e f r o m t h e b e z e l .
3.
3.
T o r e a t t a c h , p u s h b i l l a c c e p t o r b o d y f i r m l y
o n t o b e z e l u n t i l l o c k s .
Push Firmly to
Release Bezel
Figure 3