Coinco Vantage Series Manual de instalação e operação - Página 3

Procurar online ou descarregar pdf Manual de instalação e operação para Terminal de pagamento Coinco Vantage Series. Coinco Vantage Series 4 páginas.

Imprimir página

Conﬁ guring Bill Acceptance

To change the conﬁ guration settings:

1. Remove the bill box.

2. Press and release the Service Mode Button. Wait

for the green diagnostic LED to begin ﬂ ashing two

times.

3. Remove the lower housing – press the release but-

ton on the bottom side of the Vantage and slide the

lower housing out of the bill acceptor Figure 6.

4. The 5 LED's on lower housing will tell you which

setting is either on or off. Use Figure 5 as a guide to

enable or disable bill acceptance and options. If the

LED light is "on", the option is turned on. If the LED is

off, the option is turned off.

5.To advance from one page to another, with the

lower housing removed, look at the ﬂ ashing LED #5.

Press and hold the Service Mode Button on the lower

housing for 7 seconds. 1 blink means you are on

page 1. 2 blinks means you are on page 2 and so on.

Release the Service Mode Button when blinking LED

#5 indicates the page you wish to conﬁ gure.

6. To save the settings, re-install the lower housing

in the Vantage. Be careful not to press the Service

Mode Button when installing the lower housing as this

will change your settings.

• Coupon Acceptance: Enables or disables ac-

ceptance of all user-loaded coupons. If this is set to

"OFF", no coupons will be accepted.

• High Security vs. Standard Security Bill Accep-

tance: The Standard Security setting accepts 95+%

of genuine street-grade legal bills. High security mode

is recommended for locations with a higher risk of

frauds

• Bezel Lighting Mode: Use the bill inlet LEDs #3

and #4 on page 2 to select Smart Bezel, Impulse, or

Steady bezel lighting. See ﬁ g. 5 and chart below.

LED LED Mode

LED Operation

Off

Smart-4 Upper 4 individual LEDs communicate

$1, $5, $10, $20 acceptance when

enabled by host machine.

Off

Impulse Upper 4 individual LEDs blink in a

runway pattern.

Off

Smart-2 Upper two LED sets (left and right)

communicate $1 or $1&$5 acceptance

when enabled by host machine.

Steady

Upped 2 LED sets (left and right)

communicate $1 or $1&$5 acceptance.

Lower outside LEDs remain steady on.

• 1-Way/2-Way/4-Way: Deﬁnes the number of bill

orientation directions that the bill acceptor will accept.

1-Way and 2-Way are face up.

• Level 3 Security: Recommended for higher risk

environments. Provides additional level of security

against stringing and fishing attempts by blocking

access to the bill path.

Options

Configuration Settings

To Configure Options

Action

Press and release

button, diagnostic

1 .

S ervice

SERV

LED flashes

2 .

Remove Lower Housing

Set Options As Desired

3 .

(see Options Navigation and

Configuration Settings figures)

Re-install Lower Housing.

4 .

S a le s o r

Inlet LEDs flash 5 times

confirming options are saved

5 .

Test unit to ensure proper setup.

Options Navigation

S cro lls to next set o f o p tio n s

P ress

w ith in cu rre n t P a g e . E a ch o p tio n

O nce &

SERV

sh o u ld b e co n figu re d p ro p e rly

R elease

b e fo re m o vin g to th e n e xt P a g e .

P ress &

S cro lls to next Page o f o p tio n s.

H old for

SERV

next P age

Service Mode Button

SERV

Inlet LED On:

OFF

Option On (Disabled)

Bill Acceptance

Bill Inlet LEDs

$10

Coupons/Security/Bezel Lights

Bill Inlet LEDs

Coupons

High

Security

Bill Acceptance/ Orientation

Bill Inlet LEDs

2-Way

1-Way

$50

4-Way

(both on)

Level 3 Security

Bill Inlet LEDs

Level 3

Reserved

Security

Diagnostic

Mode

Light

x 2

GRN

C o

C on n f f i i g g

OFF

C onfig

OFF

GRN

R e a d y

Diagnostic LED

Figure 4

Inlet LED Off:

Option Off (Disabled)

Page 1

$20

(Flash x1)

Page 2

(Flash x2)

$100

Page 3

(Flash x3)

Page 4

(Flash x4)

Figure 5