AirStage UTY-VSGXZ1 Manual de instalação - Página 3

Procurar online ou descarregar pdf Manual de instalação para Extensor AirStage UTY-VSGXZ1. AirStage UTY-VSGXZ1 6 páginas.

Imprimir página

SELECTING AN INSTALLATION LOCATION

Dimensions

41 11

The signal amplifier is comprised of a body and cover.

Ø28 (1-3/32)

89.5

For dust proof

(3-17/32)

bushing

Ø22.2 (7/8) For conduit

241.6 (9-1/2)

272 (10-23/32) Hole pitch

288 (11-11/32)

4 - Ø5 (3/16) For M4x20mm screws

Power supply

Power consumption (W)

Operating

Temperature

Packaged

°C(°F)

Packaged

Humidity (%)

Dimensions

H x W x D mm(in1)

Weight g (oz1)

WIRING

WARNING

Before starting installation work, turn off the power of this unit and the

connection destination. Do not turn on the power again until installation

is completed. Otherwise, it will cause electric shock or fire.

Use the accessories or specified power supply cable and transmission

cables. Do not modify power supply cable and transmission cables

other than those specified, do not use extension cables, and do not use

independent branch wiring. Overcurrent may cause electric shock or fire.

Install the transmission cables securely to the terminal block. Confirm

that external force is not applied to the cable. Use transmission cables

made of the specified cable. If intermediate connection or insertion

fixing are imperfect, it will cause electric shock, fire, etc.

When connecting the power supply cable and transmission cable, route

the cables so that the cover of this unit is securely fixed. If the cover is

imperfectly fixed, it may cause fire or overheating of the terminals.

Perform earth (ground) work positively. Do not connect the earth

(ground) cable to a telephone cable, water pipe, or conductor rod.

Always fasten the outside covering of the transmission cables with the

cable clamp. (If the insulator is chafed, electric leakage may occur.)

Perform all wiring works so that the user does not touch the wiring.

Otherwise, injury or electric shock could result.

If any cable is damaged, do not repair or modify it yourself. Improper

work will cause electric shock or fire.

CAUTION

Do not bind the remote controller cable and the transmission cable

together with or parallel to the power supply cable of the indoor and

outdoor units. It may cause erroneous operation.

AMP Air Conditioning

Unit : mm (in.)

Ø28 (1-3/32)

89.5

For dust proof bushing

2-Ø5 (3/16)

For M4x20mm

screws

(2-5/8)

1Ø AC208–240V

50/60 Hz

4.5

0–46 (32–114)

-10–60 (14–140)

0–95 (RH); No condensation

67 x 288 x 211 (2-5/8 x 11-11/32 x

8-5/16)

1500 (53)

When performing wiring work, be careful not to damage the cable or

injure yourself. Also, connect the connectors securely. Loose connec-

tors will cause trouble, heating, fire, or electric shock.

Install the indoor and outdoor units, power supply cable, transmission

cable and remote controller cable 1 m (40 in.) away from television and

radio to avoid distorted images and noise. Otherwise, a malfunction

could result.

Perform wiring so that water does not enter this unit along the external

wiring. Always install a trap to the wiring or take other countermea-

sures. Otherwise it will cause trouble or electric shock or fire.

Confirm the name of each unit and name of each terminal block of the

unit and connect the wiring in accordance with the directions given

in the manual so that there is no incorrect wiring. Incorrect wiring will

damage the electric parts and cause smoke and fire.

When installing the transmission cables near a source of electromag-

netic waves, use shielded cable.

Otherwise, a breakdown or malfunction could result.

The terminal screws and earth (ground) screws have different shapes.

Be sure to install the screws in the correct locations. If the screws are

installed in the wrong locations, the PC board could be damaged.

There are some restrictions on the wiring condition.

For details, refer to the Design & Technical Manual.

Check point

51 11

▪

Arrange so that there is no transmission cable between each network

segment except the transmission cable which passed through the

signal amplifier.

▪

Arrange so that there is only 1 terminal resistor for each network seg-

ment.

Check the number of terminal resistors in each segment. If there

are more than 1 terminal resistor connected to the outdoor units and

signal amplifiers in a network segment, remove the additional terminal

resistors.

▪

Do not install a signal amplifier between 2 outdoor units in the same

refrigerant system.

▪

Install the disconnect switch to the easily accessible location.

▪

Install the fuse (3A) to the L line of power supply cable.

V Series

Signal amplifier (Filter mode : OFF)

1Ø 50/60Hz

FUSE

208-240V

(3A)

Switch

(Disconnect switch)

Indoor unit

Outdoor unit

Transmission cable

Terminal resistor

Indoor unit

V-II Series

Signal amplifier (Filter mode : OFF)

1Ø 50/60Hz

FUSE

208-240V

(3A)

Switch

(Disconnect switch)

Indoor unit

Outdoor unit

Transmission cable

Terminal

Indoor unit

resistor

www.ampair.co.uk | [email protected]

Terminal

resistor

Indoor unit

Refrigerant system

NS 2

NS 1

Terminal resistor

Terminal

resistor

Indoor unit

Refrigerant system

NS 2

NS 1

Terminal

resistor

En-2