Anchor ProLink 500 Network Manual do Proprietário - Página 3
Procurar online ou descarregar pdf Manual do Proprietário para Sistema de intercomunicação Anchor ProLink 500 Network. Anchor ProLink 500 Network 6 páginas. Wireless intercom
Imprimir páginaProLink 500™ Wireless Intercom Owners Manual
BASIC SETUP AND OPERATION
1. Charge the batteries 5-6 hours.
Note: Belt packs operate about ten to twelve hours of
continuous use per charge. (Diagram 2)
2. Find the MASTER belt pack as indicated on the top label. The
Master belt pack must be ON for each of the REMOTE belt
packs to function. (Diagram 1)
3. Plug headset cable into belt pack & adjust boom. (Diagram 2)
4. Turn on power and set headset volume. Power ON LED is
solid green and flashing green for LOW battery. (Diagram 1)
5. Set slide switch to Push to Talk or Always On mode.
(Diagram 3)
6. Choose channel A or B for all belt packs. If both channels are
used at the same time, two master belt packs are required
(See page 6). (Diagram 1)
Note: repeat above for each member's belt pack in use.
BELT PACK CONTROLS
Mic Gain – controls the microphone sensitivity. Someone with a soft
voice will increase the Mic Gain.
Power Knob also controls headset volume. The Power LED is solid
green while ON and flashes green when batteries need recharging.
A/B Channel Selection – each member of the system must be on the
same channel to hear communication
RX/TX LED – flashes RED when transmitting and is SOLID RED on the
Remote belt packs when out of range of the Master belt pack
PTT control – push to engage in conversation and release when done
Push to Talk or Always ON slide switch for the mode of operation
preferred. If you want hands free operation, select the Always On mode.
Your belt pack is live at all times.
4-PIN XLR headset connector - use Anchor Audio headsets or any
headset with a dynamic microphone.
Charging Port for the GC-9000 gang charger – charge LED glows RED
when charging and stops glowing when charge complete.
HEADSETS
ProLink 500 uses noise cancelling headsets with a 4-pin XLR connector.
Models H-2000 (dual ear muff) and H-2000S (single ear muff) are
available. The headsets include an adjustable boom microphone.
ON/OFF/VOLUME CONTROL
MIC GAIN CONTROL
PROLINK 500 BELT PACK
Model Shown: BP-500M
BLUETOOTH SETUP
1. Turn ON the BT headset and put it in pairing mode to pair ("CONNECT") with ProLink 500 beltpack.
Note: Every Bluetooth headset has its own pairing procedure. Refer to instructions.
2. The BT will auto pair with the ProLink 500 if the BT headset has been already paired to the ProLink 500 beltpack.
3. RED LED will turn ON (see on the back side of ProLink 500) in a few seconds indicating that it has paired.
4. After the RED LED turns ON push the CONNECT button to activate the audio.
5. If you want to switch to the wired headset on the same beltpack you will have to turn
OFF/disconnect the BT headset.
6. If you want to pair a new BT headset push "DISCONNECT" to delete current pairing before you start the pairing process.
For System Setup & Operation Videos Visit Our Website: www.anchoraudio.com
D I A G R A M 1
RX/TX LED (RED)
"PUST TO TALK " BUTTON
CHANNEL SELECTOR
POWER LED (GREEN)
D I A G R A M 2
XLR CONNECTOR
CHARGING PORT
CHARGING LED (RED)
MADE IN USA
TWO YEAR WARRANTY
D I A G R A M 3
"PUST TO TALK " OR
ALWAYS ON SLIDE SWITCH
BATTERY COMPARTMENT
BELT CLIP
BLUETOOTH
PAIRING
PANEL
3