Dreame U20 Manual do utilizador - Página 9

Procurar online ou descarregar pdf Manual do utilizador para Aspirador de pó Dreame U20. Dreame U20 10 páginas. Cordless stick vacuum

Imprimir página

Installing the Dust Cup, Pre-

Filter, and Cyclone Assembly

• Install the cyclone assembly and pre-

filter into the dust cup.

Fig. E-5

• Slightly tilt the dust cup so the slot aligns

with the clip on the vacuum. Then gently

push the dust cup until it clicks into

place.

Fig. E-6

Cleaning the Filter

It is recommended to clean the filter once

every 4 to 6 months.

• Remove the dust cup as shown in the

figure.

Fig. E-7

• Remove the filter from the vacuum by

pulling it down in the direction shown in

the figure.

Fig. E-8

• Rinse the filter with rotating it 360°.

Lightly tap the filter several times to

remove any debris caught in it.

Fig. E-9

Note:

1. Only use clean water to wash the filter.

Do not use detergent.

2. Do not attempt to clean the filter with

a brush or finger.

• Allow the filter to air dry for 24 hours.

Fig. E-10

Installing the Filter

• Insert the filter into the vacuum.

Fig. E-11

• Reinstall the dust cup.

Fig. E-12

Replacing the Battery Pack

The vacuum contains a removable

rechargeable lithium-ion battery pack

which has a limited number of recharge

cycles. After extended use, the battery

pack may no longer hold a charge. If this

happens, it means the battery pack has

reached the end of its life cycle and needs

to be replaced.

• Press down the battery pack release

button and slide the battery pack to the

right, as illustrated, to remove it.

• Install the new battery pack.

Fig. E-13

Cleaning the Multi-Surface

Brush

• Turn the lock counterclockwise until it

stops, then remove the brush roller from

the brush.

Fig. E-14

• Use scissors to cut off hairs and fibers

tangled on the brush roller. Wipe the

dust from the notch and brush cover

with a dry cloth or paper towel.

Fig. E-15

• When it is dirty, rinse the brush roller with

clean water until it is clean.

Fig. E-16

• Stand the brush roller upright for at least

24 hours until it is fully dry.

Fig. E-17

Cleaning the Motorized

Mini-Brush

• Use a coin as illustrated to rotate the

lock counterclockwise until you hear a

click.

Fig. E-18

• After unlocking the motorized mini-

brush, remove the brush roller, then

rinse and clean it.

Fig. E-19

• Stand the brush roller upright in a well-

ventilated area for at least 24 hours until it

is fully dry.

Fig. E-20

• Once the brush roller is dry, reinstall it

by following the disassembly steps in

reverse.

Fig. E-21

Specifications

Vacuum Cleaner

Model

VPV11A

Rated Power

370 W

Rated Voltage

25.2 V

Charging Time

approximately 4 hours

Multi-Surface Brush

Model

VMR1

Rated Power

40 W

Rated Voltage

25.2 V

Motorized Mini-Brush

Model

VPA1

Rated Power

20 W

Rated Voltage

25.2 V

Charger

Model

ZD012M300065EU

100-240 V

50/60 Hz

Input

0.5 A

Output

30 V

0.65 A

Average Active

85.36%

Efficiency

Efficiency at Low

75.35%

Load (10%)

No-load Power

0.1 W

Consumption

Rechargeable Lithium-Ion Battery Pack

Model

V2316-7S1P-SCA

Nominal Voltage

25.2 V

Nominal Capacity

2500 mAh

Rated Capacity

2300 mAh

Energy

57.96 Wh