Dyna-Glo EG4800DGP Manual de instruções de instalação e manutenção - Página 3
Procurar online ou descarregar pdf Manual de instruções de instalação e manutenção para Aquecedor elétrico Dyna-Glo EG4800DGP. Dyna-Glo EG4800DGP 19 páginas. Portable unit heater
Imprimir página
Prior to operating heater, make sure the electrical outlet is of the configuration
and capacity appropriate for the heater. See outlet configuration on front page
of manual. This heater is for use on 240 volts. The cord has a plug as shown in
Figure 1. No adapter is available for this blade configuration, and none should
be used. The type outlet is a 240 volt grounding outlet. When properly installed,
it provides a ground connection through the cord to the heater to protect the
operator from electric shock.
The heater is for floor mounting. Place the heater on floor or other flat surface and insert plug into the proper wall
outlet.
BE CAREFUL NOT TO DIRECT THE AIRSTREAM AT DRAPERIES, FURNITURE, OR OTHER OBJECTS
THAT COULD BE DAMAGED BY HEAT. DO NOT PLACE THE HEATER WHERE A SMALL CHILD MAY FALL
OVER THE HEATER. DO NOT PLACE THE HEATER WHERE THE POWER CORD MAY BE WALKED ON.
TRIPPED OVER OR THERWISE SUBJECTED TO HARD USAGE.
OPERATING INSTRUCTIONS
The heater must be properly installed before it is used.
The heater must be properly installed before it is used.
Set thermostat to its full counterclockwise position. Plug the unit into a properly grounded 240V outlet. (#6-20
Set thermostat to its full counterclockwise position. Plug the unit into a properly grounded 240V outlet. (#6-30 for
for model EG4000D, #6-30 for model EG4800DG and EG5300DG). Set the thermostat to the farthest
model EG4800DGP). Set the thermostat to the farthest clockwise position. The fan shuld come on and the unit
clockwise position. The fan should come on and the unit will start heating the room. When the room reaches
will start heating the room. When the room reaches comfort level, turn the thermostat counterclockwise until the
comfort level, turn the thermostat counterclockwise until the heater turns off. The heater will cycle
heater turns off. The heater will cycle automatically around this preset temperature. To increase temperature,
automatically around this preset temperature. To increase temperature, turn the thermostat knob clockwise. To
turn the thermostat knob clockwise. To lower temperature, turn the thermostat counterclockwise. Do not attempt
lower temperature, turn the thermostat counterclockwise. Do not attempt to tampering with the thermostat.
to tampering with the thermostat.
MAINTENANCE INSTRUCTIONS
The heater should be cleaning twice for a year. Turn thermostat off and remove plug from electrical outlet and
make sure that the heating element of the heater is cool before cleaning heater. Use a soft cloth for dusting. For
cleaning, use only a damp rag and non-abrasive dish
may harm the finish. If heater is used in very dusty location, use a vacuum cleaner dust brush to remove dust and
other foreign material from the grilles. Always unplug cord and wrap around heater handle when not in use. Move
heater to a safe location for storage.
This heater does not require any routine maintenance other than occasional cleaning to prevent clogging of intake
grille opening. To clean air intake grille, use vacuum with brush attachment or high pressure air. The motor is
permanently lubricated. Do not operate the heater with a damaged cord or plug or if the heater malfunctions or has
been damaged in any manner. Return heater to authorized service facility for examination, electrical, or
mechanical adjustment, or repair.
OPERATION OF THE SAFETY THERMAL LIMIT CONTROL INDICATES THE HEATER HAS BEEN
SUBJECTED TO SOME ABNORMAL CONDITIONS. IT IS RECOMMENDED THAT THE HEATER BE
CHECKED BY A REPUTABLE ELECTRICIAN OR REPAIR SERVICE TO INSURE THE HEATER HAS NOT
BEEN DAMAGED.
GENERAL
FLOOR APPLICATION
WARNING
CLEANING AND STORAGE
detergent. Do not use abrasive chemical cleaners as these
SERVICE
WARNING
3
GROUNDING
PIN
Figure 1
Figure 1.