Emergi-Lite EMIU-250W Manual de instruções - Página 2

Procurar online ou descarregar pdf Manual de instruções para Inversor Emergi-Lite EMIU-250W. Emergi-Lite EMIU-250W 12 páginas. Mini inverter

Imprimir página

WARNING:

CAUTION:

IMPORTANT:

Emergi-Lite®

Tel: (888) 552-6467

THE MINI INVERTER MUST BE MOUNTED SECURELY USING A 1/4" (MIN) SCREW AND FLAT

WASHER FOR EVERY KEYHOLE. THE MOUNTING SURFACE MUST ALSO BE SUFFICIENTLY

REINFORCED TO ACCOMODATE THE WEIGHT LISTED (SEE PAGE 1). FAILURE TO SECURE THE

UNIT SUFFICIENTLY CAN DAMAGE THE EQUIPMENT AND/OR CAUSE SERIOUS INJURY.

DO NOT ENERGIZE THE CIRCUIT UNTIL ALL STEPS HAVE BEEN SUCCESSFULLY COMPLETED.

DO NOT RELY SOLELY ON THE INVERTED T-BAR STRUCTURE TO SUPPORT THE UNIT. FAILING TO

INSTALL WIRE SUPPORTS CAN LEAD TO SERIOUS INJURY.

FAILURE TO CONNECT THE BATTERY(S) PROPERLY MAY RESULT IN EQUIPMENT FAILURE OR

AN UNSAFE CONDITION AND WILL VOID THE WARRANTY. A SMALL SPARK MAY OCCUR WHEN

CONNECTING TO THE BATTERY WIRES. THIS IS NORMAL AND IS CAUSED BY LARGE

CAPACITORS CONTAINED IN THE MINI INVERTER BEING CHARGED.

ALWAYS TURN OFF THE INVERTER MODULE AND THE AC SUPPLY TO THE EQUIPMENT AND

DISCONNECT THE BATTERY BEFORE SERVICING. ONLY QUALIFIED SERVICE TECHNICIANS

SHOULD SERVICE THIS EQUIPMENT. THE USE OF PARTS SUPPLIED BY OTHER THAN THE

MANUFACTURER MAY RESULT IN AN UNSAFE CONDITION OR EQUIPMENT FAILURE AND WILL

VOID THE WARRANTY.

THIS UNIT PROVIDES MORE THAN ONE POWER SUPPL Y OUTPUT SOURCE. TO REDUCE THE

R I S K OF ELECTRICAL SHOCK WHEN SERVICING, DISCONNECT BOTH NORMAL AND

EMERGENCY SOURCES BY TURNING OFF THE A.C. BRANCH CIRCUIT AND BY DISCONNECTING

THE B AT T E RY.

BEFORE INSTALLING, MAKE CERTAIN THE A.C. POWER IS OFF.

NOTE: THE BATTERY(S) ARE SHIPPED SEPARATELY. PLACE THEM IN A LOCATION AWAY FROM

THE WORK AREA TO AVOID DAMAGE UNTIL THEY ARE TO BE INSTALLED.

ONLY ONE VOLTAGE IS ALLOWED (120V OR 277V). CONNECTION TO MORE THAN ONE VOLTAGE

MAY RESULT IN EQUIPMENT FAILURE AND VOID THE WARRANTY.

FOR NORMALLY ON UN-SWITCHED UNITS: THE JUMPER WIRE IS PRESET FOR 120VAC. IF THE

UNIT IS TO BE WIRED FOR 277VAC, REMOVE THE JUMPER WIRE FROM THE 120VAC INPUT

POWER TERMINALS AND REINSTALL THE JUMPER WIRE INTO THE 277VAC INPUT POWER

TERMINALS.

IF CONNECTED TO 277V INPUT, USE A 277V RATED SWITCH. FAILURE TO USE THE PROPER

VOLTAGE SWITCH MAY RESULT IN SWITCH FAILURE, A SHOCK HAZARD, AN UNSAFE

CONDITION AND/OR EQUIPMENT FAILURE.

THE MINI INVERTER HAS A SELF-TEST FEATURE AND CAN ENTER IN SELF-TEST MODE (MONTHLY,

BIANNUAL OR ANNUAL) AT ANY TIME. WHEN THIS OCCURS, POWER WILL BE AVAILABLE AT THE

OUTPUT OF THE MINI INVERTER, EVEN IF THE LATTER WAS CONFIGURED FOR NORMALLY-OFF

OPERATION. ALWAYS TURN OFF THE INVERTER MODULE INSIDE THE MINI INVERTER BEFORE

WORKING WITH THE WIRING SYSTEM OF THE EMERGENCY LIGHTING SYSTEM.

WHEN MAKING CONNECTIONS TO THE MINI INVERTER, YOU MUST RESPECT THE

APPROPRIATE WIRING DIAGRAMS. DO NOT CONNECT THE "INPUT POWER" NEUTRAL TO THE

"LOAD" NEUTRAL. FAILURE TO COMPLY WITH THIS DIRECTIVE MAY RESULT IN EQUIPMENT

FAILURE AND VOID THE WARRANTY.

FOR NORMALLY OFF LOAD: REMOVE THE JUMPER WIRE BEFORE WIRING THE UNIT.

Fax: (800) 316-4515

www.emergi-lite.com

EMIU 125/250/400W Mini Inverter

06/18 750.1782 Rev. J

2/12