IKEA IHW6362WM0 Instruções de instalação e manual de utilização e cuidados - Página 7
Procurar online ou descarregar pdf Instruções de instalação e manual de utilização e cuidados para Campânula de ventilação IKEA IHW6362WM0. IKEA IHW6362WM0 28 páginas. 30" (76 cm), 35 7/16" (90 cm) wall-mount canopy range hood
Imprimir página
10. Attach two mounting hooks to the wall at location marked on
the template.
A
B
...................... i ........
A. Mounting hooks
B. Centerline on wall
Vent Cover Support Bracket
Installation
Installations using telescoping
upper and lower vent cover
assembly
1. Position vent cover bracket on wall about 1/8"(3.0 mm) away
from the ceiling.
2. Mark the hole locations.
3. Drill 3/8"(9.5 mm) holes for wall anchors and insert anchors
flush with the wall.
,
A
e-.. e _::D ................
C
A. 10.0 x 60.0 mm drywall anchors
B. Centerline on wall
C. Vent cover support bracket
D. 6.0 x 70.0 mm screws
4. Attach vent cover support bracket to wall.
Installation
locations
with reduced
ceiling heights
NOTE: Either the lower or the upper vent cover can be used for
such installation but note that upper vent cover is smaller than
the lower vent cover. There will be more clearance were the upper
vent cover attaches on top of the range hood.
For non-vented (recirculating) installations:
The vent hood is installed using the upper vent cover
(26" [66.0 cm]) plus a %" (10.0 mm) thick wood filler.
1. For the vent cover to slide down and engage the top of the
hood, the vent cover bracket must be installed 2/8"(10.0 mm)
below the ceiling.
2. The remaining space above the vent cover can be filled with a
2/8"(10.0 mm) thick piece of plywood cut to the inside cross
section of the chimney cover and finished to match the
ceiling.
For vented installations:
The vent hood is installed using the lower vent cover
(163/4"[42.5 cm]) plus a 2/8"(10.0 mm) thick wood filler.
1. For the vent cover to slide down and engage the top of the
hood, the vent cover bracket must be installed 2/8"(10.0 mm)
below the ceiling.
2. The remaining space above the vent cover can be filled with a
2/8"(10.0 mm) thick piece of plywood cut to the inside cross
section of the chimney cover and finished to match the
ceiling.
3=
Cut the self adhesive rubber tape supplied with the hood in 4
identical pieces. Attach 2 pieces of tape to each side of the
support bracket.
A
_
..................................
S
A. Vent cover bracket
B. Rubber tape
Vented Installations
Install transition on top of hood (if removed for shipping) with
2 sheet metal screws.
Non-Vented (recirculating) Installations
1. Install transition on top of hood (if removed for shipping) with
2 sheet metal screws.
2. Attach the vent cover ceiling bracket to the deflector with the
two 3.5 x 9.5 mm screws provided.
B
C
A. Vent cover bracket
B. 3.5 x 9.5 mm screws
C. Deflector
3. Connect the deflector to the transition with 6" (15.2 cm)
round vent once hood has been set in place.
Complete
Preparation
1. Determine and make all necessary cuts in the wall for the vent
system. Install the vent system before installing the hood. See
"Venting Requirements"
section.
2. Determine the required height for the 1/2"conduit and drill a
1V4" (3.2 cm) hole at this location.
3. Run wire through the 1/2"conduit according to the National
Electrical Code or CSA Standards and local codes and
ordinances. There must be enough 1/2"conduit and wires from
the fused disconnect
(or circuit breaker) box to make the
connection
in the hood's electrical terminal box.
NOTE: Do not reconnect power until installation is complete.
4. Use caulk to seal all openings.