AlienPro RG STAR Manual do utilizador - Página 3

Procurar online ou descarregar pdf Manual do utilizador para Equipamento de DJ AlienPro RG STAR. AlienPro RG STAR 3 páginas.

Imprimir página
Attention
2. Please do not see the laser beam directly to avoid and damage.
3. Before connect or disconnect the power, please adjust the luminace of the laser diode to the least
to avoid any damage to the laser diode.
4. This unit should be keep dry, do not use in the rain and dusty environment. It can be use in the
outdoor with the water - proofcover protector.
5. Set the light immobility and try to avoid strong shake or hit.
6. Prevent dust into the equipment to avoid problems.
7. Please keep that there´s no other equipment or decorating materials obstructed the exhaust fan
and the vent - pipe when the equipment was working.
8. Before connect power, check the plug is immobility or not, power line should be connect well.
9. Please do not open or close the equipment frequently that´s to avoid any affect to the life span of
the laser diode, any try the best to avoid the long time working.
10. Due to the characteristic of the laser diode, after for ours working, it should be close at least 25
minutes until the laser diode cooling then work again.
11. Don´t touch the light or draw the power line when your hand was wet. And do not pull the
electronic power line.
12. Maintain the distance at least 3M above from the equipment to the object.
13. This equipment does not have any parts can repair for the users, please do not open the equip-
ment.
14. When the laser diode became dim or damge please contact the dealer timely.
15. When you want to retransfer the products, you´d better use the original package to shockproof.
Function Instructions
1. When dip switch No. 10 is set to the "ON" position, the unit works in auto mode.
2. When all dip switches are set to the "OFF" position, the unit works in sound - active mode.
3. Auto-play (Master - Slave synchronization): when master laser dip switch setting to No. 10, the
light will run the settled program automatically, meanwhile, it will have DMX512 signal´s output. Just
one ligth could be settled to be master. Setting salve: you should put dip switch No. 1 in "on".
5. Address code function mode setting
Mode
1 DMX-512 mode、Slave mode
2 Sound active mode、Master mode 1-10:OFF
3 Auto play mode、Master mode
4 Square test pattern
5 Dot text pattern
w w w . a l i e n p r o . c o m . m x
Binary code（ON）
1-9:Setting address code
10:OFF
1-9:OFF
10:ON
9、10:ON
1、2、3、4、5、6、7、8:OFF
8、9、10:ON
1、2、3、4、5、6、7:OFF
2
Channel Instruction
Channel
Value
0～64
64～127
CH1
128-191
192-255
CH2
0～255
0~63
64~127
CH3
128-191
192-255
0~127
CH4
128~191
192~255
0~127
CH5
128~255
0~127
CH6
128~255
0~127
CH7
128~255
0~127
CH8
128~255
Maintenance
Maintenance should be performed every 15 - day period, by using a sponge wich is dipped woth
alcohol, rather than wet cloth or other chemical liquid, to clean the mirror. Always disconnect from
the mains when the device is not in use or before cleaning it.
Warning
Power must be disconnected before maintenance or repair. Do not look at the light source direct-
ly. To prevent or reduce the risk of electrical shock or fire, do not expose this unit to high
temperature/rain or moisture.
Note
Don´t separate laser machine from laser power and repair them by yourself, otherwise no good
repair service will be supplied.
Description
Close light
Auto-play
Sound active
Patterns control
Choose patterns
Choose patterns size
From small to large,speed up rate
From large to small,speed up rate
Large – small – large, speed up rate
Choose rotation angle
Auto clockwise rotation, speed up rate
Auto anti-clockwise rotation, speed up rate
Choose horizontal position
Horizontal move,speed up rate
Choose Vertical position
Vertical move,speed up rate
Choose horizontal roll position
Horizontal roll ,speed up rate
Choose Vertical roll position
Vertical roll,speed up rate
w w w . a l i e n p r o . c o m . m x
3