AlienPro RG STAR Kullanıcı Kılavuzu - Sayfa 3

DJ Ekipmanları AlienPro RG STAR için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. AlienPro RG STAR 3 sayfaları.

Sayfayı Yazdır

Attention

2. Please do not see the laser beam directly to avoid and damage.

3. Before connect or disconnect the power, please adjust the luminace of the laser diode to the least

to avoid any damage to the laser diode.

4. This unit should be keep dry, do not use in the rain and dusty environment. It can be use in the

outdoor with the water - proofcover protector.

5. Set the light immobility and try to avoid strong shake or hit.

6. Prevent dust into the equipment to avoid problems.

7. Please keep that there´s no other equipment or decorating materials obstructed the exhaust fan

and the vent - pipe when the equipment was working.

8. Before connect power, check the plug is immobility or not, power line should be connect well.

9. Please do not open or close the equipment frequently that´s to avoid any affect to the life span of

the laser diode, any try the best to avoid the long time working.

10. Due to the characteristic of the laser diode, after for ours working, it should be close at least 25

minutes until the laser diode cooling then work again.

11. Don´t touch the light or draw the power line when your hand was wet. And do not pull the

electronic power line.

12. Maintain the distance at least 3M above from the equipment to the object.

13. This equipment does not have any parts can repair for the users, please do not open the equip-

ment.

14. When the laser diode became dim or damge please contact the dealer timely.

15. When you want to retransfer the products, you´d better use the original package to shockproof.

Function Instructions

1. When dip switch No. 10 is set to the "ON" position, the unit works in auto mode.

2. When all dip switches are set to the "OFF" position, the unit works in sound - active mode.

3. Auto-play (Master - Slave synchronization): when master laser dip switch setting to No. 10, the

light will run the settled program automatically, meanwhile, it will have DMX512 signal´s output. Just

one ligth could be settled to be master. Setting salve: you should put dip switch No. 1 in "on".

5. Address code function mode setting

Mode

1 DMX-512 mode、Slave mode

2 Sound active mode、Master mode 1-10:OFF

3 Auto play mode、Master mode

4 Square test pattern

5 Dot text pattern

w w w . a l i e n p r o . c o m . m x

Binary code（ON）

1-9:Setting address code

10:OFF

1-9:OFF

10:ON

9、10:ON

1、2、3、4、5、6、7、8:OFF

8、9、10:ON

1、2、3、4、5、6、7:OFF

Channel Instruction

Channel

Value

0～64

64～127

CH1

128-191

192-255

CH2

0～255

0~63

64~127

CH3

128-191

192-255

0~127

CH4

128~191

192~255

0~127

CH5

128~255

0~127

CH6

128~255

0~127

CH7

128~255

0~127

CH8

128~255

Maintenance

Maintenance should be performed every 15 - day period, by using a sponge wich is dipped woth

alcohol, rather than wet cloth or other chemical liquid, to clean the mirror. Always disconnect from

the mains when the device is not in use or before cleaning it.

Warning

Power must be disconnected before maintenance or repair. Do not look at the light source direct-

ly. To prevent or reduce the risk of electrical shock or fire, do not expose this unit to high

temperature/rain or moisture.

Note

Don´t separate laser machine from laser power and repair them by yourself, otherwise no good

repair service will be supplied.

Description

Close light

Auto-play

Sound active

Patterns control

Choose patterns

Choose patterns size

From small to large,speed up rate

From large to small,speed up rate

Large – small – large, speed up rate

Choose rotation angle

Auto clockwise rotation, speed up rate

Auto anti-clockwise rotation, speed up rate

Choose horizontal position

Horizontal move,speed up rate

Choose Vertical position

Vertical move,speed up rate

Choose horizontal roll position

Horizontal roll ,speed up rate

Choose Vertical roll position

Vertical roll,speed up rate

w w w . a l i e n p r o . c o m . m x