Brother DCP-7025 Manual de configuração rápida - Página 4
Procurar online ou descarregar pdf Manual de configuração rápida para Impressora Brother DCP-7025. Brother DCP-7025 34 páginas. Brother dcp-7010: quick start
Também para Brother DCP-7025: Perguntas frequentes e resolução de problemas (4 páginas)
Imprimir página
Regulations
IEC 60825 specification (220 to 240 volt model only)
This machine is a Class 1 laser product as defined in IEC 60825
specifications. The label shown below is attached in countries where it is
needed.
CLASS 1 LASER PRODUCT
APPAREIL À LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
This machine has a Class 3B laser diode which produces invisible laser
radiation in the scanner unit. You should not open the scanner unit under any
circumstances.
Warning
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
☛ Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
☛ Varning
Om apparaten används på annat sätt än i denna
Bruksanvisning specificerats, kan användaren utsättas för
osynlig laserstrålning, som överskrider gränsen för
laserklass 1.
Internal laser radiation
Maximum radiation power: 5 mW
Wave length:
770 - 810 nm
Laser class:
Class 3B
Warning
IMPORTANT - For Your Safety
To ensure safe operation the supplied three-pin plug must be inserted only
into a standard three-pin power outlet that is properly grounded through the
normal household wiring.
Extension cords used with this machine must be three-pin plug type and
correctly wired to provide proper grounding. Incorrectly wired extension
cords may cause personal injury and equipment damage.
The fact that the equipment operates satisfactorily does not imply that the
power is grounded and that the installation is completely safe. For your
safety, if in any doubt about the effective grounding of the power, call a
qualified electrician.
Disconnect device
You must install this machine near a power outlet that is easily accessible. In
case of an emergency, you must disconnect the power cord from the power
outlet to shut off the power completely.
IT power system (For Norway only)
This product is also designed for an IT power system with phase-to-phase
voltage 230V.
Wiring information (for UK)
Important
If you need to replace the plug fuse, fit a fuse that is approved by ASTA to
BS1362 with the same rating as the original fuse.
Always replace the fuse cover. Never use a plug that does not have a cover.
Warning - This machine must be earthed.
The wires in the mains lead are coloured in line with the following code:
Green and Yellow:
Earth
Blue:
Neutral
Brown:
Live
If in any doubt, call a qualified electrician.
Radio interference (220-240 volt model only)
This machine follows EN55022 (CISPR Publication 22)/Class B.
Before you use this product, make sure that you use the following interface
cables.
1. A shielded parallel interface cable with twisted-pair conductors and that it
is marked "IEEE 1284 compliant".
2. A USB cable.
The cable must not be more than 2 meters long.
®
International E
S
Compliance Statement
NERGY
TAR
E
The purpose of the International
NERGY
development and popularization of energy-efficient office equipments.
®
E
S
As an
Partner, Brother Industries, Ltd. has determined that
NERGY
TAR
E
S
this product meets the
NERGY
TAR
®
S
Program is to promote the
TAR
®
guidelines for energy efficiency.