Brother DCP-7025 Hızlı Kurulum Kılavuzu - Sayfa 4

Yazıcı Brother DCP-7025 için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Brother DCP-7025 34 sayfaları. Brother dcp-7010: quick start
Ayrıca Brother DCP-7025 için: SSS & Sorun Giderme (4 sayfalar)

Sayfayı Yazdır

Regulations

IEC 60825 specification (220 to 240 volt model only)

This machine is a Class 1 laser product as defined in IEC 60825

specifications. The label shown below is attached in countries where it is

needed.

CLASS 1 LASER PRODUCT

APPAREIL À LASER DE CLASSE 1

LASER KLASSE 1 PRODUKT

This machine has a Class 3B laser diode which produces invisible laser

radiation in the scanner unit. You should not open the scanner unit under any

circumstances.

Warning

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

For Finland and Sweden

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

☛ Varoitus!

Laitteen käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

☛ Varning

Om apparaten används på annat sätt än i denna

Bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för

laserklass 1.

Internal laser radiation

Maximum radiation power: 5 mW

Wave length:

770 - 810 nm

Laser class:

Class 3B

Warning

IMPORTANT - For Your Safety

To ensure safe operation the supplied three-pin plug must be inserted only

into a standard three-pin power outlet that is properly grounded through the

normal household wiring.

Extension cords used with this machine must be three-pin plug type and

correctly wired to provide proper grounding. Incorrectly wired extension

cords may cause personal injury and equipment damage.

The fact that the equipment operates satisfactorily does not imply that the

power is grounded and that the installation is completely safe. For your

safety, if in any doubt about the effective grounding of the power, call a

qualified electrician.

Disconnect device

You must install this machine near a power outlet that is easily accessible. In

case of an emergency, you must disconnect the power cord from the power

outlet to shut off the power completely.

IT power system (For Norway only)

This product is also designed for an IT power system with phase-to-phase

voltage 230V.

Wiring information (for UK)

Important

If you need to replace the plug fuse, fit a fuse that is approved by ASTA to

BS1362 with the same rating as the original fuse.

Always replace the fuse cover. Never use a plug that does not have a cover.

Warning - This machine must be earthed.

The wires in the mains lead are coloured in line with the following code:

Green and Yellow:

Earth

Blue:

Neutral

Brown:

Live

If in any doubt, call a qualified electrician.

Radio interference (220-240 volt model only)

This machine follows EN55022 (CISPR Publication 22)/Class B.

Before you use this product, make sure that you use the following interface

cables.

1. A shielded parallel interface cable with twisted-pair conductors and that it

is marked "IEEE 1284 compliant".

2. A USB cable.

The cable must not be more than 2 meters long.

International E

Compliance Statement

NERGY

TAR

The purpose of the International

NERGY

development and popularization of energy-efficient office equipments.

As an

Partner, Brother Industries, Ltd. has determined that

NERGY

TAR

this product meets the

NERGY

TAR

Program is to promote the

TAR

guidelines for energy efficiency.