2N SmartGate Início rápido - Página 2

Procurar online ou descarregar pdf Início rápido para Porta de entrada 2N SmartGate. 2N SmartGate 2 páginas.

Imprimir página

SmartGate QuickStart

Read the CD-ROM User Manual carefully to get familiar with all system functions.

Security Precautions

• Do not switch on SmartGate in the vicinity of medical

apparatuses to avoid interference. The minimum distance

of the antenna and pacemakers should be 0.5 m.

• Do not switch on SmartGate aboard a plane.

• Do not switch on SmartGate near petrol stations, chemical

facilities or sites where explosives are used.

• Any mobile telephone use prohibition based on RF energy

radiation applies to SmartGate too.

• SmartGate may disturb the function of TV sets, radio sets

and PCs.

• Warning! SmartGate contains components that can be

swallowed by small children (SIM card, antenna, etc.).

• The voltage value mentioned on the power adapter may

not be exceeded. If you connect SmartGate to another

power supply, make sure that the voltage value is in the

acceptable range.

• When your SmartGate comes to the end of its operational

life, dispose of it in accordance with applicable regulations.

Basic Functions

• The primary purpose of SmartGate is to

transmit voice between a GSM network

and connected telecommunication devices.

• You can

establish

data connections

(GPRS, CSD) and send/receive SMS in

combination with a PC.

• You can send an SMS to a pre-

programmed number using the SMS

sending input.

• Models of SmartGate with fax converter

can

transmit

fax

messages

using

analog fax Group 3 on telephone line.

External Antenna Connection

Screw the antenna into the SMA antenna

connector. Tighten the antenna connector

gently with your hand, never use spanner!

Use antenna with coax cable if the GSM

signal is poor, or in case of interference.

SIM Card Installation

Open

the

SIM

card

holder

SmartGate's back side, insert the SIM

card and close the holder properly.

Select the required GSM provider and

SIM

card

services,

such

call

forwarding,

call

barring,

preferred

networks, SMS centre, etc. using your

mobile phone before inserting your SIM

card in SmartGate.

A SmartGate delivery contains:

SmartGate

Antenna for direct

connection

Antenna with coax cable

Supply adapter

Telephone cable

PC-connection serial cable

SMS sending input

connector

Dowels

Screws

SW programs and User

Manual on a CD-ROM

QuickStart manual +

mounting pattern

Warranty certificate

Proper Location

• SmartGate is designed for vertical mounting on

suspension holes (use the mounting pattern). This

position is the best for GSM signal reception.

• Install SmartGate with respect to a good GSM signal

strength.

• Place SmartGate out of range of sensitive devices and

human bodies for electromagnetic interference reasons.

• SmartGate is designed for indoor use. Do not place it

near heat sources and on sites exposed to direct solar

radiation. It may not be exposed to rain, flowing water

and moisture. In addition, it may not be exposed to

aggressive gas, acid vapours, solvents, etc.

Telephone Lines Connection

Connect

any

FXO-interface

equipment

telephone set, answering machine, PBX CO line,...) to

FXS interface (Phone icon) on SmartGate. To FXO interface

on SmartGate (crossed out Phone icon) connect FXS-

interface equipment (internal line of PBX). SmartGate is

equipped with CLIP via FSK on FXS interface and so it is

advantageous to connect a terminal that is able to display the

CLI.

Power Supply Connection

SmartGate is powered with 10-16V DC voltage. Where a

source other than the included supply adapter is used, the

voltage range and polarity shown on the SmartGate supply

connector have to be maintained. Do not switch on the power

supply until the antenna is connected to SmartGate to avoid

the GSM module damage.

SIM Card PIN protection

1. Hook off the telephone, you can hear the PIN

tone:

1 pc

2. Enter the PIN using the DTMF and press a

for confirmation. To cancel a wrong PIN hang

1 pc

up the telephone line.

3. If you hear the busy tone in a while (a few

1 pc

seconds), you have entered the PIN correctly.

1 pc

The PIN will be entered automatically upon the

2 pc

next power up.

1 pc

4. If you hear the PIN tone again in a while, you

1 pc

have entered a wrong PIN. Re-enter the PIN.

Phone calls – DialThru gateway

2 pcs

Initial SmartGate behavior is like that:

2 pcs

• Calls from FXS interface are routed to GSM

1 pc

network.

• Incoming calls from GSM rings on FXS

1 pc

interface.

• In case of incoming ringing on FXO interface,

1 pc

both analog interfaces on SmartGate are

interconnected. So ringing is transferred to

FXS interface and FXO-FXS call is enabled.

For advanced calls routing you have to

program

Routing

distributors may preprogram tables for usual

use in your country.

• SmartGate is able to route calls according to

phone number prefix. Calls from FXS interface

can be routed not only to GSM network, but

also to FXO interface. It is necessary to

program FXS routing table for this.

• ME – Mobility Extension is new useful

function on our gateways. If ME is activated

and incoming call rings on FXO interface,

SmartGate routes this call to FXS interface and

simultaneously

network. You can receive the call on analog

(standard

line as well as on your mobile phone.

Phone calls – gateway for PBX internal line

You can switch SmartGate from DialThru

gateway to gateway for PBX internal line by

setting of only one parameter. You can find it on

FXO routing table page.

• Calls from FXO interface are routed to GSM

network.

• If incoming calls from GSM network have to be

routed back to FXO interface, it is moreover

necessary to program the Other CLI's row in

GSM routing table. (If you want SmartGate to

route incoming GSM calls according to CLI, fill

in GSM routing table rows, as you need).

The manufacturer, 2N TELEKOMUNIKACE a.s, hereby declares that the 2N SmartGate equipment is in

compliance with the essential requirements and other relevant provisions of the 1999/5/EC Directive.

The Declaration of Conformity is available on CD-ROM and at website www.2n.cz.

Analogue FAX and Data Connection (optional)

SmartGate with fax converter has ability to

manage fax messages using analogue fax

Group 3 and data connection using analogue

modem connected to telephone line. The fax or

data service must be registered with your GSM

operator.

Outgoing FAX Call and Data Connection

Before destination number dial code *01* for fax

call or *02* for data connection.

Incoming FAX Call and Data connection

It is recommended to activate separate fax

number on your SIM card –multinumbering

scheme. Fax messages and data connection

should be routed to appropriate number.

It is possible to set fax engine in the gateway to

receive the next call as fax or data call or make

this setting permanent - see the manual on CD.

Indication LEDs

Power

supply

tables.

Some

local

GSM

network

establishes

call

GSM

Phone

line

• Light is on whenever SmartGate is

on.

• light = registered to GSM

• flashes once in 1s = not registered,

SIM card inserted

• flashes once in 3s = not registered,

SIM card not inserted

• flashes 4 / 8 times quickly = enter

your PIN / PUK

• no light = standby

Orange for FXS interface:

• flashes quickly = line off-hook or

ringing

• light = call FXS – GSM

• flashes once in 3s = data connection

in progress

On FAX models:

• Flashes 2 times then pause = fax

connection in progress; after power

on signalize need of FW upgrade

Green for FXO interface:

• flashes quickly = line off-hook or

ringing

• light = call FXO – GSM

Alternately orange and green:

• quickly = ringing from FXO is

connected to FXS interface

• slowly = call FXS – FXO