Dialogic PBX Integration Board D/82JCT-U Cartão de instalação rápida

Procurar online ou descarregar pdf Cartão de instalação rápida para Placa de rede Dialogic PBX Integration Board D/82JCT-U. Dialogic PBX Integration Board D/82JCT-U 2 páginas. Pbx integration board

Imprimir página

Dialogic

D/82JCT-U

PBX Integration Board

Quick Install Card

Part Number: 64-0089-02

Dialogic Corporation. All

rights reserved.

Before You Begin

Protecting the Board from Damage

CAUTION:

All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-

sensitive boards and components at a static-safe

work area,

and observe anti-static precautions at all times.

If you are not familiar with ESD safety precautions,

visit

http://www.dialogic.com/support/hwinstall

to learn

more.

Unpacking the Board

Unpack the Dialogic

D/82JCT-U PBX Integration

board ("board") according to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the

board by the edges and avoid touching the

board's components.

Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when

carrying boards from station to station.

CAUTION: Do not remove the board from the anti-

static packaging until you are ready to install it.

Observe proper anti-static precautions at all times.

Physical Description

Board ID

Display

Pin 1

PCI bus connector

Rear bracket

Configuring the Hardware

The Dialogic

D/82JCT-U board is a PCI form factor

board that uses hardware auto-configuration for IRQ

and memory address. It allows you to use the factory

default hardware settings for quick installation and

operation. However, you should review the following

information to determine if any of the optional

configuration items apply to your system.

Setting the Board Identification Number

When you start a Dialogic

board, each board is

assigned a Board ID number for identification and use

by the application program.

All Dialogic

PCI boards with a rotary switch can

share the factory default switch setting and Board ID

of 0. To give a PCI board with a rotary switch a Board

ID other than 0, the rotary switch is set to the desired

number. Because the Dialogic

D/82JCT-U board has

no rotary switch, the Dialogic

Configuration Manager

(DCM) software that is provided with the board

automatically assigns Board IDs, beginning with 0,

unless there are other PCI boards with a rotary switch

settings of 0, 1, 2, etc. In that case, DCM assigns the

first available Board ID not in use.

The Board ID of the Dialogic

D/82JCT-U can only be

changed by using DCM. See the DCM help files for

more information about changing Board IDs.

Note: If you add PCI boards with rotary switches to

your system after Dialogic

D/82JCT-U boards have

been assigned, boards may share the same ID,

depending on the rotary switch settings of the new

boards. For instance, if DCM has assigned Board IDs

01, 02, and 03 to existing Dialogic

D/82JCT-U

boards, and then the rotary switches on three new

J1: 36-position mini-D plug

connector

P8: CT Bus termination jumpers.

CT Bus connector

Bus signals are terminated when

jumper clip is installed over

indicated pins

Note: Bus signals must be

terminated only on boards at each

P8 Detail

end of the CT Bus cable.

Pin 2

Pin 4

Pins 1 & 2—CT Bus/SCbus

termination

Pin 3

Pins 3 & 4—MVIP Bus termination

CT Bus connector: ECTF H.100-

compliant CT Bus edge connector

boards are set to 1, 2, and 3, the Dialogic

and new boards will share Board IDs 01, 02, and 03.

The Dialogic

D/82JCT-U Board ID appears on the 2-

character LED display on the rear bracket of the

board, along with error codes, when appropriate.

Display

Meaning

00-xx

Board ID (in hexadecimal)

PCI Bus reset active

Front-end download or initialization

failed

E1-E8

Error on PBX port 0-7 (channel 1-8)

Following download, the Board ID is continuously

displayed on the LED unless a communications error

is experienced on one or more of the PBX ports.

When errors are present, they are displayed for two

seconds, alternating with the Board ID for two

seconds.

CT Bus Termination

Jumpers are used to terminate signals on the CT Bus.

These settings apply to boards located at physical

ends of the bus. For CT Bus or SCbus, both

CT_C8_(A&B) and CT_FRAME_(A&B) are terminated

using pins 1 and 2 of the P8 termination jumpers. For

MVIP, C-2 and C-4* are terminated using pins 3 and 4

of the P8 termination jumpers.

Note: Only the two boards at the ends of the CT Bus

ribbon cable must have their terminations enabled. All

other boards must not have the jumper clips installed.

Installing the Board

1. Working with your computer at a static-safe work

area, switch off the power and disconnect all

power cords from the electrical outlets.

2. Remove the chassis cover.

3. Select an empty PCI expansion bus slot and

remove the slot's retaining screw and access

cover plate.

4. If you are not installing your board in an ISA form

factor PCI slot, remove the ISA edge retainer

bracket from the board.

5. Using the slot's board guides, insert the edge

connector of the board into the bus slot. Press

firmly until the board is securely seated in the slot.

6. Replace and tighten the retaining screw to secure

D/82JCT-U

the board firmly in the chassis slot. If the screw is

not installed, attaching a CT Bus cable can unseat

the board from the slot.

Installing the PCI Board

Remove

Cover

Plate

Computer

Chassis

7. Repeat steps 3–6 for each board you are

installing.

Connecting the CT Bus Cable

Note: If you are using the Dialogic

"stand-alone" mode, where the application does not

use time-slot routing, you do not need to connect a

CT Bus cable and you may skip the instructions in this

section. You only need to perform this part of the

installation if your system uses multiple boards and

controls resources on the boards through time-slot

routing.

The Dialogic

D/82JCT-U connects to other boards

via the H.100-compliant Computer Telephony bus (CT

Bus) using an optional CT Bus cable.

PCI

Board

PCI Slot

ISA Slot

D/82JCT-U in