Dialogic PBX Integration Board D/82JCT-U Cartão de instalação rápida - Página 2

Procurar online ou descarregar pdf Cartão de instalação rápida para Placa de rede Dialogic PBX Integration Board D/82JCT-U. Dialogic PBX Integration Board D/82JCT-U 2 páginas. Pbx integration board

Imprimir página

Note: Full H.100 capabilities are not available with

this release of the Dialogic

D/82JCT-U.

1. Attach the end connector on the ribbon cable to

the CT Bus edge connector on the top edge of the

first board. The connectors are designed to fit

together one way only. If the connector does not

seat fully on the board, turn the cable around and

try again. Make sure that the colored stripe on the

cable faces toward the rear bracket. (The stripe

should be adjacent to pin 1 on the board

connector.) To preserve the electrical integrity of

the CT Bus, use a CT Bus cable with the

appropriate number of connectors ("drops"). It is

recommended that no more than two connectors

at either end of the cable be left unused.

2. Attach the ribbon cable to the next board until all

boards are connected by the cable.

Installing the CT Bus Cable

CT Bus

Colored

Cable

Stripe

(Pin 1)

NOTE:

Your CT Bus cable may

have a different number

of connectors (drops).

Note: To connect the CT Bus to an SCbus, attach

a CT Bus/SCbus Adapter (not included) to the CT

Bus board closest to the SCbus, and connect the

SCbus cable to this adapter. See the hardware

installation instructions for the CT Bus/SCbus

Adapter for more information.

3. If the ribbon cable has extra connectors or loose

cable, tuck the cable down so that it does not snag

when you replace the PC cover.

4. After installing and connecting all the boards,

replace the PC cover, cables, and cords.

Connecting External Cabling

A PBX station interface cable assembly that is specific

to the Dialogic

D/82JCT-U (available separately) is

used to connect the board to a punch-down block.

Connecting the Station Interface Cable

To punch-down block

28 GA 18-pair

shielded cable

D/82U rear bracket

36-position

mini-D cable plug

25-pair telco plug

The station interface cable terminates at the punch-

down block end with a 25-pair, 57-series Amphenol

plug to allow available type-66 punch-down blocks to

be used to terminate the PBX station wiring. A 36-

position mini-D connector is used on the Dialogic

D/82JCT-U end of the cable.

To connect your Dialogic

D/82JCT-U board to a

punch-down block, follow the instructions below:

1. Connect the station interface cable's 36-position

mini-D cable plug to the connector on the rear

bracket of the Dialogic

D/82JCT-U.

2. Connect the station interface cable's 25-pair telco

plug to the connector on the punch-down block.

Hardware installation is now complete.

Connector Pin Numbering

25-pair connector

(attaches to the punch-down block)

36-position connector

(attaches to the D/82U)

The Telco plug cable connector tabulation is arranged

so that the four conductors of one station set circuit

are adjacent on a standard, type-66 punch-down

block. The pattern shown in the following figure

continues down the connector to encompass all eight

channels with two pairs of conductors per channel, for

a total of 16 twisted conductor pairs.

Telco Plug Connector Pinout

Ch. 1: 4-wire transmit

Ch. 1: 2-wire transmit/receive

or Ch.1: 4-wire receive

Ch. 2: 4-wire transmit

Ch. 2: 2-wire transmit/receive

or Ch. 2: 4-wire receive

After Installing the Hardware

After installing the hardware, run the Dialogic

Configuration Manager (DCM) as described in the

installation instructions included with the Dialogic

System Software to configure your system.

For technical specifications and product information

go to: http://www.dialogic.com/products.htm.

Warranty and Return

Information

Warranty Period

For specific warranty information for this board, refer

to the Warranty section of the Products page, located

at this URL: http://www.dialogic.com/warranties/.

Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who are

trained to answer technical questions on installing and

configuring Dialogic

products. If you are unsure how

to contact your support channel, please call Dialogic

in the United States at 973-967-6600 (9am-5pm EST)

and we will assist in obtaining the appropriate support

channel.

Outside the United States please refer to

http://www.dialogic.com/support/contact

local contact information. Dialogic also provides direct

support via Dialogic

Pro™ Services agreements. For

more details of direct support from Dialogic please

refer to:

http://www.dialogic.com/support/DialogicPro.

Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following:

http://www.dialogic.com/support/hwfaults.

Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales

Office for your area. Address, telephone and fax

numbers, are available at the Dialogic website located

at: http://www.dialogic.com/contact.htm.

To purchase Dialogic

products, please refer to the

following website to locate the appropriate supplier:

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use only

and are subject to change without notice and do not represent a

commitment on the part of Dialogic Corporation or its subsidiaries

("Dialogic"). Reasonable effort is made to ensure the accuracy of the

information contained in the document. However, Dialogic does not

warrant the accuracy of this information and cannot accept

responsibility for errors, inaccuracies or omissions that may be

contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN

CONNECTION WITH DIALOGIC

EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO

ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY

THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED

AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC

ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC

DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY,

RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS

INCLUDING LIABILITY OR WARRANTIES RELATING TO

FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY,

OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY

RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life

sustaining, critical control or safety systems, or in nuclear facility

applications.

It is possible that the use or implementation of any one of the concepts,

applications, or ideas described in this document, in marketing

collateral produced by or on web pages maintained by Dialogic may

infringe one or more patents or other intellectual property rights owned

by third parties. Dialogic does not provide any intellectual property

licenses with the sale of Dialogic products other than a license to use

such product in accordance with intellectual property owned or validly

licensed by Dialogic and no such licenses are provided except pursuant

to obtain

to a signed agreement with Dialogic. More detailed information about

such intellectual property is available from Dialogic's legal department

at 9800 Cavendish Blvd., 5

Floor, Montreal, Quebec, Canada H4M

2V9. Dialogic encourages all users of its products to procure all

necessary intellectual property licenses required to implement any

concepts or applications and does not condone or encourage any

intellectual property infringement and disclaims any responsibility

related thereto. These intellectual property licenses may differ

from country to country and it is the responsibility of those who

develop the concepts or applications to be aware of and comply

with different national license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol,

among others, are either registered trademarks or trademarks of

Dialogic. Dialogic's trademarks may be used publicly only with

permission from Dialogic. Such permission may only be granted by

Dialogic's legal department at 9800 Cavendish Blvd., 5th Floor,

Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's

trademarks will be subject to full respect of the trademark guidelines

published by Dialogic from time to time and any use of Dialogic's

trademarks requires proper acknowledgement. The names of actual

companies and products mentioned herein are the trademarks of their

respective owners.

PRODUCTS. NO LICENSE,