Aquatec 8800 Manual de instruções de instalação - Página 2
Procurar online ou descarregar pdf Manual de instruções de instalação para Bomba de água Aquatec 8800. Aquatec 8800 2 páginas. Pab8800 series ro booster pump
Imprimir página
Read the OPERATIONAL AND INSTALLATION GUIDELINES carefully before starting to install the pump. Consult
the Factory if there is any question.
1. Determine the optimum location for your pump before proceeding.
Note: Locate the pump after the sediment pre-filter and before the carbon pre-filter (If part of R.O. system).
2. Turn off water.
3. Cut the 1/4" or 3/8" O.D. flexible tubing in sufficient length to avoid any stress on the tubing where it connects to the
pump or the fitting on any accessory.
4. Insert tubing into pump ports. If fittings are John Guest type, be sure tubing is inserted past the resistance point until it
bottoms out against the port stop. If the compression fittings with threaded nuts are used, insert tubing until it bottoms
out in the port and hand tighten the compression nut until the connection is tight. Then tighten the nut 1/2 turn
clockwise or follow the wrench tightening instructions provided by fitting manufacturer.
5. The "CDP" pump is now ready for operation. Open feed-water valve to allow water to flow through the R.O. system
(Open flow-restrictor by-pass valve if part of R.O. system).
6. If the power source is a transformer, plug the appropriate Aquatec supplied/approved transformer into the receptacle
and connect the pump to the transformer. If the power source is not a transformer, connect the pump to the
appropriate power source. Allow water to circulate, purging any entrapped air. For pumps equipped with our "AFT"
auto- flush, the flow restrictor by-pass will open and close automatically when the transformer is plugged in.
7. The pump will now start building pressure. Operating pressure will vary with membrane flow rate, flow restrictor flow
rate, feed-water pressure and line voltage. Check for fitting leaks.
Note: If the flow restictor is too small (We recommend 300Ml/min. for standard CDP 6800 series pumps and
500Ml/min. for CDP 8800 series pumps), or if the R.O. systems is clogged, an internal pump bypass mechanism limits
the output pressure.
8. If compression fittings with threaded nuts are used, observe any leaks after pump has run for approximately 15
minutes. Further tighten compression nuts approximately 1/8 to 1/4 of a turn on all fittings in the system. Wait 15
minutes and repeat the leak check.
Note: Further adjustments should not be necessary although it may take several days of operation before all air has
been purged and the system is stabilized.
SERVICING:
Every Year: Check system against operating standards.
Every 2-3 Years: Replace diaphragm and check against operating standards.
AQUATEC WARRANTY
Aquatec Water Systems, Inc. ("Aquatec") warrants its products to be free from defects in material an workmanship under
the following terms:
Series 58XX, 68XX, 88XX, 55XX, ERP 1000, ERP 500 as well as PFR/TLC and PAW: The warranty will last for a period
of thirteen months from date of shipping from an Aquatec warehouse with the exception that the period will be extended
for an additional twelve months for 68XX series, ERP 500 and ERP 1000. Aquatec's obligation under this warranty shall
be limited to replacing or repairing at Aquatec's discretion, any such product or part which is returned to Aquatec's
factory with a Return Material Authorization Number (RMA), transportation charges approved by Aquatec or prepaid, and
upon examination, is found to Aquatec's satisfaction to have been defective under the terms of this warranty. No credit
will be allowed against future purchases for items returned as defective under the terms of Aquatec's warranty.
This warranty does not extend to any products, which have been altered or modified outside the Aquatec
factory, nor does it apply to units that are returned in an unassembled condition. Furthermore, the warranty does
not extend to pumps that are identified by a 9XXX model number, indicating non-compliance with Aquatec's Engineering
Standards. This includes, but is not limited to, pumps ordered without an integral control mechanism. The warranty
guarantees that products will perform to Aquatec's flow and pressure specifications throughout the life of the warranty.
The warranty does not cover wear, appearance, misapplication or external water damage. If the returned product is
found not to be defective under the conditions of this warranty, a charge will be made for repair or replacement.
This is a Limited Warranty. It covers the product only and the extent of the coverage is limited to the cost of the
product. As the manufacturer has no control over shipping, handling and installation, the warranty cannot cover
water damage, or any other damage, caused by a leak or other malfunction.
This warranty is in lieu of all other warranties, expressed or implied, and no person is authorized to give any other
warranty or assume obligation or liability in Aquatec's behalf. Aquatec shall not be liable for any indirect, incidental or
consequential damages of any kind incurred by the reason of the use or sale of any defective product and part.
2